Cyanoacrylate

Incure Heat-Resist 340: High-Temperature Metal Adhesive

Most instant adhesives soften and lose grip well before 100 degrees Celsius. Incure Heat-Resist 340 is a high-viscosity cyanoacrylate formulated to hold structural loads through thermal shock and sustained heat, in the kind of environment that defeats a standard grade. What Heat-Resist 340 Is Heat-Resist 340 is a single-part, high-viscosity cyanoacrylate. It cures at room temperature through contact with trace surface moisture, reaching handling strength quickly and full strength over the following hours. No mixing, no light, and no oven step are required, which makes it well suited to manual assembly and moderate-rate production of metal parts. The formulation trades some of the raw speed of a thin cyanoacrylate for two things that matter on real hardware: a thick, gap-tolerant body and a cured polymer that keeps its strength at elevated temperature. Key Properties Bond strength up to 5,200 psi on select plastics, with strong performance on common engineering metals when surfaces are clean and lightly abraded. High viscosity. The adhesive stays where it is placed, bridges imperfect fit-up, and can be applied to vertical surfaces without running. This suits machined parts where the gap is not zero. Thermal resistance. The cured bond resists thermal shock and retains a usable fraction of its room-temperature strength at temperatures that would soften a general-purpose cyanoacrylate. Chemical resistance. Withstands occasional contact with alcohols, petrol, aromatic hydrocarbons, and dilute acids and bases after full cure. Rapid cure. Reaches fixture strength in seconds to minutes depending on gap, humidity, and substrate. Meets Mil-A-46050C, the defense specification for cyanoacrylate adhesives covering viscosity, strength, and cure behavior. Where It Fits Heat-Resist 340 is aimed at metal bonding in demanding thermal and mechanical conditions: Automotive and aerospace components near heat sources or subject to vibration, such as brackets, clips, sensor mounts, and trim retention Industrial equipment and machinery where parts run hot and cannot be welded without distortion Oil and gas hardware exposed to heat and hydrocarbon contact Defense equipment requiring a qualified adhesive with documented performance For joints that carry sustained structural load rather than retention or tacking duty, a two-part epoxy is often the better tool. Our comparison of which adhesive is stronger for heavy-duty repairs explains where each chemistry belongs. Getting a Reliable Bond Prepare the surface. Degrease with a fast-flashing solvent, then lightly abrade metal to remove oxide and add mechanical key. Wipe again and let the surface dry. Control the gap. High viscosity tolerates an imperfect fit, but cyanoacrylate cure slows and weakens as the bond line grows past a few tenths of a millimeter. Keep the joint tight and use an activator on wider gaps. Manage humidity. Cyanoacrylate cure depends on ambient moisture. Very dry conditions slow cure; an accelerator restores speed. Very humid conditions can flash-cure the surface before parts mate. Allow full cure before loading. Handling strength comes fast, but full thermal and chemical resistance develops over 24 hours. Do not heat-cycle or solvent-expose the joint before then. If you need to confirm Heat-Resist 340 suits a specific metal pair…

Comments Off on Incure Heat-Resist 340: High-Temperature Metal Adhesive
August 15, 2024
Cyanoacrylate

Heat-Resistant Glue for Plastic: Incure Heat-Resist™ 328

Bonding plastic that will run hot is a two-part problem: the adhesive has to grip a low-energy surface, and it has to keep gripping it at 100°C and above. Heat-resistant glue for plastic has to solve both, and Incure Heat-Resist™ 328 is formulated for exactly that combination. The Two Failure Modes to Design Around Plastic-to-plastic bonds that fail hot usually fail one of two ways. Either the adhesive never wet the surface properly, so the bond is weak from the start, or the cured film softens as temperature rises and the joint creeps under load. A general-purpose cyanoacrylate is vulnerable to both. Heat-Resist™ 328 addresses the second with a modified cyanoacrylate chemistry that holds a large fraction of its strength through sustained heat, and the first is handled with correct surface preparation. It is a single-component, medium-viscosity adhesive that cures at room temperature through ambient moisture, with no mixing and no pot life. Incure Heat-Resist™ 328 at a Glance Chemistry: single-component, room-temperature-cure cyanoacrylate Viscosity: medium, for controlled placement and small gap filling Fixture speed: seconds to tens of seconds depending on substrate and humidity Bond strength: up to roughly 5,200 psi on suitable rigid plastics Thermal behavior: engineered for thermal-shock resistance and elevated continuous service Chemical resistance: withstands alcohols, aliphatic fuels, aromatic hydrocarbons, and dilute acids and bases Matching the Adhesive to the Plastic Surface energy drives everything. ABS, polycarbonate, PVC, acrylic, and most filled engineering resins bond well after a solvent wipe. Nylon and acetal need light abrasion and often a primer. Polyethylene, polypropylene, TPO, and PTFE are low-energy and require a dedicated polyolefin primer before the adhesive will hold. Glass-filled grades bond more like the base resin but benefit from a slightly thicker film to fill surface texture. For dissimilar-plastic joints, thermal expansion is the hidden load. A rigid plastic bonded to a flexible one over a wide temperature range puts continuous stress on the bond line even when the assembly is doing nothing, so review how CTE mismatch causes adhesive bond failure during joint design. If you are also weighing chemistry options, UV glue versus epoxy for transparent bonding covers the trade-offs on clear plastics. Application and Cure Control Clean both faces with isopropyl alcohol and let them flash off. Apply one thin drop or bead to a single face, mate within the open time, and hold light fixture pressure until handling strength develops. Full strength and peak heat resistance build over 24 hours; a short 80–100°C post-cure accelerates that on production lines. Keep shop humidity between 40 and 60 percent, and use an activator on primed polyolefins or wider gaps. Meter each dispensed shot on automated equipment so film thickness stays repeatable. Where Heat-Resist™ 328 Fits Automotive: under-hood plastic housings, ducts, and clips near heat sources Appliance manufacturing: plastic components in ovens, dryers, and cooktops that see cyclic heat Industrial equipment: plastic guards, covers, and fixtures in warm process areas Consumer electronics: internal plastic structure near power supplies and processors Lighting: plastic housings and lenses adjacent…

Comments Off on Heat-Resistant Glue for Plastic: Incure Heat-Resist™ 328
August 15, 2024
Cyanoacrylate

Black Heat-Resistant Glue: Incure Heat-Resist™ 320

When a bond line will be visible on a finished product and the assembly runs hot, a clear adhesive that yellows or blooms is a cosmetic liability. Black heat-resistant glue solves both problems at once, and Incure Heat-Resist™ 320 pairs a pigmented finish with genuine elevated-temperature performance. Why Color Matters at the Bond Line Standard cyanoacrylate cures clear but is prone to frosting, or blooming, as monomer vapor settles on nearby surfaces and reacts with ambient moisture. On a dark housing or a machined casting, that white haze stands out. A black-pigmented grade hides the joint, masks minor squeeze-out, and gives line operators and inspectors an immediate visual cue that adhesive is present and correctly placed. Heat-Resist™ 320 is a single-component, medium-viscosity cyanoacrylate that cures to an opaque black film. It carries the same modified chemistry as the rest of the Heat-Resist™ line, so the color is not a trade-off against thermal capability. Incure Heat-Resist™ 320 at a Glance Chemistry: single-component, room-temperature-cure cyanoacrylate, black Viscosity: medium, for controlled placement and small gap filling Fixture speed: seconds to tens of seconds depending on substrate and humidity Bond strength: up to roughly 5,200 psi on suitable rigid plastics Thermal behavior: engineered for thermal-shock resistance and elevated continuous service Chemical resistance: withstands alcohols, aliphatic fuels, aromatic hydrocarbons, and dilute acids and bases Substrates and Joint Design Heat-Resist™ 320 bonds most engineering thermoplastics, elastomers, cured composites, and prepared metals. Keep the bond line thin, between 0.05 and 0.15 mm, and load the joint in shear. Because the film is rigid, add a mechanical feature to carry peak load on any joint that flexes in service. Prime low-surface-energy plastics such as polyolefins before bonding. The opaque film also blocks light, which matters when a joint sits next to an optical path or a sensor window. For assemblies that mix rigid and flexible plastics with a wide temperature range, read how CTE mismatch causes adhesive bond failure so differential expansion does not overload the joint. Application and Cure Control Wipe both faces with isopropyl alcohol and let them dry. Dispense one thin drop or bead on a single face; over-application cures slowly and can still bloom despite the pigment. Mate within the open time, hold light fixture pressure, and allow 24 hours for full strength and peak heat resistance. A brief 80–100°C post-cure speeds the climb to full properties on a production line. Hold shop humidity between 40 and 60 percent for repeatable fixture times. Use an activator on inactive surfaces or where the gap exceeds what the adhesive bridges alone. On automated equipment, meter each shot so the cured film thickness stays consistent part to part. For a broader view of how cure speed and working time trade off, see which adhesive dries faster for quick repairs. Where Heat-Resist™ 320 Fits Consumer electronics: visible seams on dark enclosures that sit near warm power components Automotive: trim, clips, and sensor mounts in the engine bay where appearance and heat both matter Industrial equipment: machinery housings and…

Comments Off on Black Heat-Resistant Glue: Incure Heat-Resist™ 320
August 15, 2024
Cyanoacrylate

Heat-Resistant Cyanoacrylate Glue: Incure Heat-Resist™ 319

Standard cyanoacrylate loses most of its strength above 80°C, which rules it out for anything mounted near a motor, an exhaust path, or a power supply. Heat-resistant cyanoacrylate glue closes that gap, and Incure Heat-Resist™ 319 is built specifically for assemblies that run hot in service. Why Standard Cyanoacrylate Fails at Temperature A conventional ethyl cyanoacrylate bond begins to soften as the polymer approaches its glass transition. By 90–100°C, lap-shear strength can drop to a third of its room-temperature value, and continuous exposure drives slow thermal degradation of the cured film. For a part that sees 120°C or repeated thermal cycling, that decline is a field-failure risk rather than a spec-sheet footnote. Heat-Resist™ 319 uses a modified cyanoacrylate chemistry that holds a far larger fraction of its strength through sustained heat and survives rapid temperature swings without crazing at the bond line. It is a single-component adhesive, so there is no mixing, no pot life, and no ratio error to control on the line. Incure Heat-Resist™ 319 at a Glance Chemistry: single-component, room-temperature-cure cyanoacrylate Viscosity: medium, for controlled placement and modest gap filling Fixture speed: seconds to tens of seconds depending on substrate and humidity Bond strength: up to roughly 5,200 psi on suitable rigid plastics Thermal behavior: engineered for thermal-shock resistance and elevated continuous service Chemical resistance: withstands alcohols, aliphatic fuels, aromatic hydrocarbons, and dilute acids and bases Specification: formulated to meet Mil-A-46050C for military and defense assembly Substrates and Joint Design Heat-Resist™ 319 bonds most engineering thermoplastics, elastomers, cured composites, anodized aluminum, and steel. Thin bond lines perform best: target 0.05–0.15 mm and design the joint so the adhesive works in shear rather than cleavage or peel. For low-surface-energy plastics such as polypropylene or PTFE, use a compatible primer first. When a joint must absorb ongoing flexing, pair the bond with a mechanical feature that carries peak load, since cyanoacrylate films are rigid. If your parts combine metal and plastic with a wide service-temperature range, review how CTE mismatch causes adhesive bond failure before finalizing the joint, because differential expansion can load the bond line harder than the working stress does. Application and Cure Control Clean both faces with isopropyl alcohol and let them flash off fully. Apply a single thin drop or bead to one side only; excess adhesive cures slowly, blooms, and lowers strength. Mate the parts within the open time and hold light fixture pressure until handling strength develops. Full cure and peak thermal performance continue over the following 24 hours. A short post-cure at 80–100°C can accelerate the rise to full strength on production lines. Relative humidity between 40 and 60 percent gives the most consistent cure. Very dry air slows fixture; very humid air speeds it but can promote blooming and whitening around the joint. An activator restores speed on inactive surfaces, on acidic substrates such as some chromate coatings, and on gaps wider than the adhesive can bridge on its own. On automated lines, dispense a metered shot rather than a free-hand…

Comments Off on Heat-Resistant Cyanoacrylate Glue: Incure Heat-Resist™ 319
August 15, 2024