Optical Adhesives / UV Adhesives / UV Curing Equipments / UV LED Equipments / UV LED Spot Equipments

Precision Optical Bonding: Holding Sub-Micron Alignment Through Cure

In a precision optical assembly, the adhesive is not just a fastener. It is a dimensional reference. If it shrinks a few microns as it cures, or creeps under load over months, the alignment it was supposed to preserve is gone. Precision optical bonding is about choosing and using an adhesive that moves as little as possible. The Alignment Problem Active alignment positions an optic to a fraction of a micron, then commits that position with adhesive. Every source of adhesive movement works against that: Cure shrinkage pulls the elements together as the polymer network forms Thermal expansion shifts alignment with every temperature change Creep lets a loaded joint slowly relax over time Moisture uptake swells the layer and changes its dimensions A precision bonding adhesive is formulated to minimize all four. Properties of a Precision Optical Adhesive Incure formulates the Optik line of light-curable optical adhesives, including grades developed for precision alignment work. The relevant characteristics are: Very low linear shrinkage, so the act of curing barely moves the elements On-demand cure under UV, visible, or LED light, giving the operator time to complete alignment before committing the joint, then a fast set 100 percent solids, acid-free chemistry with no VOCs, no outgassing, and no corrosion risk to adjacent metals or coatings Tack-free cure for a clean, handleable finished joint Compatibility with dissimilar substrates of different stiffness, bonding glass to metal, ceramic, or semiconductor mounts Low CTE and moisture resistance for alignment that holds through service Fast final cure with production lamps to keep cycle time reasonable Process Discipline Fixture and align under the lamp. The assembly should reach its aligned position with the cure lamp already in place, so there is no handling step between alignment and cure to disturb it. Use the minimum effective bond line. A thinner uniform layer shrinks less in absolute terms and creeps less under load. Spacers set the target. Cure in stages if needed. A brief low-dose tack holds alignment; a full-dose cure then develops final properties without a sudden shrinkage jump. Control temperature during and after cure. Bonding at a stable, known temperature and characterizing the assembly's behavior across the operating range is the only way to predict in-service alignment. The underlying mechanism is covered in how CTE mismatch causes adhesive bond failure. For help selecting a precision bonding adhesive and building an alignment-and-cure sequence, Email Us with your alignment tolerance and substrate details. Measuring and Compensating for Shrinkage Even an very low-shrinkage adhesive shrinks a little, and in precision work that residual movement has to be characterized rather than ignored. The practical method is to bond representative parts while monitoring the aligned degree of freedom, then record how far it moves from the moment of cure through full property development, which can continue for hours or days. Once that shrinkage vector is known, two options exist. Either pre-bias the alignment by that amount so the part lands on target after the adhesive settles, or design the joint so shrinkage acts…

1 Comment
August 21, 2024
Optical Adhesives / UV Adhesives / UV Curing Equipments / UV LED Equipments / UV LED Spot Equipments

Optical Bonding: Process Fundamentals and Adhesive Selection

Optical bonding replaces mechanical mounts and air gaps with a cured adhesive layer that becomes part of the optical path. Done well, it improves image quality, ruggedness, and alignment stability. Done poorly, it introduces stress birefringence, wavefront error, and delamination. The difference is in the process and the material. Why Bond Optics Instead of Clamping Them A bonded optic is held over its full contact area rather than at a few clamp points, which spreads load, damps vibration, and removes the risk of point stress on brittle glass. Eliminating air gaps removes reflective interfaces, raising transmission and contrast. And a cured bond locks alignment in place, holding it through shock and handling far better than a mechanical mount that can shift. The cost is that the adhesive is now optically and structurally critical, and the bond is generally permanent. Adhesive Properties for Optical Bonding Clarity and transmission across the working wavelengths, with no yellowing Refractive index matched to the substrates to control reflection Low cure shrinkage, so bonding does not move the elements or distort the wavefront Low CTE and a glass transition above the service range for alignment stability Viscosity matched to the joint: a high-viscosity grade bridges a defined gap or holds a vertical joint, while a thin grade wicks into mated surfaces Toughness to absorb vibration and thermal-cycling stress without cracking Incure formulates the Optik line of light-curable optical adhesives across this range, including higher-viscosity grades for gap-filling and structural optical joints. Running the Process Prepare surfaces. Solvent-clean glass and, for humidity resistance, plasma-treat or prime it. Clean and prime metal or ceramic mounts. Meter and place the adhesive. Dispense a controlled volume so the joint fills completely without excess squeeze-out into the aperture. Fixture for alignment and bond line. Hold the elements in their designed relationship with spacers setting a uniform gap. For a high-viscosity grade, the fixture mainly maintains position while the adhesive holds the gap on its own. Cure with line of sight. Light must reach the whole bonded area through a transparent element. Provide a secondary cure path for shadowed regions, and manage oxygen inhibition at exposed edges with an inert blanket or added dose. Inspect. Check for voids, fringes from stress, and edge fillet quality, and qualify with the actual thermal and vibration profile. The dominant long-term failure mode is stress from expansion mismatch between the optic and its mount, explained in how CTE mismatch causes adhesive bond failure. For help developing an optical bonding process for a specific assembly, Email Us with your optics, mounts, and environmental requirements. Inspecting a Bonded Optic A bonded optical joint is inspected on three levels. Visually and under magnification, look for voids, trapped particles, incomplete fillets, and adhesive in the clear aperture. Between crossed polarizers, look for the colored fringe patterns that reveal stress birefringence in the glass; a heavily stressed bond shows strong, concentrated fringes near the bond edge and predicts poor thermal-cycling life. Functionally, measure the transmitted wavefront through an interferometer before and…

Comments Off on Optical Bonding: Process Fundamentals and Adhesive Selection
August 21, 2024
Optical Adhesives / UV Adhesives / UV Curing Equipments / UV LED Equipments / UV LED Spot Equipments

Optically Clear Adhesive for Displays: How Direct Bonding Improves Readability

An air gap between a cover lens and a display panel is a stack of reflective surfaces. Each one bounces light back at the viewer, washing out contrast in sunlight and adding parallax. Optically clear adhesive (OCA) fills that gap, sharply improving a display's readability and ruggedness. What Direct Optical Bonding Does Laminating the cover lens directly to the display or touch sensor with a clear adhesive eliminates the internal air-to-glass interfaces. Because the adhesive's refractive index is close to that of the glass, light passes through instead of reflecting. The result is higher measured contrast ratio in ambient light, deeper blacks, no visible gap for dust or condensation to occupy, and a stiffer stack that resists impact and flex better than an air-gap assembly. Properties That Matter in an OCA Refractive index matched to the cover and panel glass, typically near 1.5, to suppress reflection High transmission and low haze across the visible range, with no yellowing after cure or aging Low shrinkage, so lamination does not induce stress patterns (mura) or distort the panel Adequate viscosity for the gap, with enough body to bridge the bond line without running Bubble-free lamination, achieved through vacuum lamination or careful roller technique Damp-heat and thermal-cycle stability, since a laminated stack that delaminates or clouds at the edges is scrap Incure Optik Clear Grades for Lamination Incure formulates the Optik line of light-curable adhesives, including optically clear grades with a medium-to-high viscosity suited to display lamination. These grades pair the index match and clarity a display needs with rapid cure under UV, visible, or LED light, low water absorption, and demonstrated stability through thermal cycling. The 100 percent solids chemistry leaves no volatiles that could fog the inside of the stack. Process Notes Clean and stage in a controlled area. Particulate is the enemy of lamination; a single fiber under the lens is a visible defect. Laminate without trapping air. Vacuum lamination is the reliable route for larger panels; small assemblies can be done with a controlled wet-out from one edge. Cure fully and evenly. Light has to reach the entire bonded area through the cover glass. A uniform dose prevents partial cure that later causes edge lift. Manage stress at the border. The cover glass, adhesive, and panel expand at different rates, and the edge of the bond concentrates that mismatch. Understanding how CTE mismatch causes adhesive bond failure informs the choice of a lower-modulus grade for large or thin panels. For help selecting an OCA for a specific stack and lamination method, Email Us with your panel size, gap, and glass types. Yellowing, Aging, and Damp Heat An OCA that looks flawless at assembly can turn faintly yellow after months of heat and light, and on a white or backlit display even a small color shift is visible. The property to specify is a low yellowing index that stays low after accelerated aging, typically a combination of elevated temperature, humidity, and light exposure meant to represent years of service in…

Comments Off on Optically Clear Adhesive for Displays: How Direct Bonding Improves Readability
August 21, 2024
Optical Adhesives / UV Adhesives / UV Curing Equipments / UV LED Equipments / UV LED Spot Equipments

Optically Clear Adhesives for Industrial Manufacturing

On an industrial line, an optically clear adhesive often has to bond more than glass to glass. It joins glass to metal brackets, plastic lenses to circuit boards, and windows to FR4 housings in one pass, staying clear through the plant's temperature and humidity extremes. A multi-substrate clear adhesive makes that practical. The Multi-Substrate Requirement Single-purpose adhesives force an assembly to be broken into steps: one material for the glass joint, another for the metal, a third for the plastic. A multi-substrate optically clear adhesive collapses that into a single dispense-and-cure operation, which cuts cycle time, simplifies the bill of materials, and removes the compatibility problems that arise where two different adhesives meet. To do this the adhesive has to wet and bond dissimilar surface energies, from high-energy metal and glass to lower-energy engineering plastics, and hold all of those interfaces through service. What Incure Optik Clear Grades Offer Incure formulates the Optik line of light-curable adhesives, including optically clear grades built for mixed-substrate industrial bonding: Multi-substrate adhesion to metals, glass, many plastics, and FR4 in one application, with lap-shear strength into the thousands of psi High clarity with no yellowing, so the bond works in a visible optical path Acid-free chemistry that will not corrode adjacent conductors or metals Tack-free cure leaving a clean, residue-free surface Rapid cure under UV, visible, or LED light, suited to inline production Low shrinkage and demonstrated toughness through thermal cycling Low water absorption and good moisture and temperature resistance Designing It Into a Process Confirm adhesion on your actual substrates. Plastics in particular vary widely; test the specific grade of polycarbonate, acrylic, or filled resin you use, in the surface condition it arrives in. Plasma or flame treatment lifts adhesion on difficult plastics. Set the bond line with the fixture. With a flowable clear adhesive, spacers or hard stops control thickness, which keeps optical path length and stress uniform. Cure with line of sight. Present the transparent element to the lamp and route a secondary cure to any shadowed area. Size the lamp to the part, whether that is a flood lamp or an inline conveyor curing system. Account for mismatch. When one substrate is metal and another is glass or plastic, their expansion rates differ, and the bond line takes the strain over temperature. The mechanism is covered in how CTE mismatch causes adhesive bond failure. For help qualifying an optically clear adhesive across your substrate set, Email Us with your material list and process conditions. Typical Applications Multi-substrate clear adhesives bond display and lens stacks to housings, cover glass to sensor modules, sight windows into equipment, and optical components onto printed circuit assemblies across industrial manufacturing. The broader comparison of UV-curable versus two-part chemistry for transparent bonding and the guide to matching a plastic-bonding grade to substrate and mechanical demand are useful when plastics are in the joint. Surface Energy and Plastic Preparation The reason a multi-substrate adhesive is harder to formulate than a glass-only one comes down to surface energy.…

Comments Off on Optically Clear Adhesives for Industrial Manufacturing
August 21, 2024
Optical Adhesives / UV Adhesives / UV Curing Equipments / UV LED Equipments / UV LED Spot Equipments

Bonding Metal to Glass: Selecting a High-Strength Optical Adhesive

Joining metal to glass is one of the harder assembly problems in optics and instrumentation. The two materials expand at very different rates, glass tolerates almost no stress before it cracks, and the joint often has to stay optically clear as well as strong. The adhesive choice is where the design succeeds or fails. Why Metal-to-Glass Is Demanding Common optical glasses expand at roughly 7 to 9 parts per million per degree C. Aluminum expands at about 23, stainless steel around 16, and titanium closer to 9. Bond aluminum to glass with a rigid adhesive and every temperature change drives a shear stress into the glass at the bond line. Over enough cycles, that stress finds a flaw and the glass chips or fractures at the edge of the bond. The joint also has to survive vibration, resist humidity at the interface, and, in many cases, transmit light without distortion. What a High-Strength Metal-to-Glass Adhesive Provides Incure formulates the Optik line of light-curable adhesives, including grades developed for structural metal-to-glass bonding. The properties that matter here are: High lap-shear strength, into the thousands of psi, on prepared glass and metal in a single application High elongation and toughness, giving the bond line enough compliance to absorb expansion mismatch and damp vibration rather than transmitting it to the glass Demonstrated thermal-cycling performance, holding bond integrity through repeated temperature extremes High clarity, so the same adhesive works in an optical path Low linear shrinkage for precise alignment Moisture and temperature resistance for outdoor and industrial service Rapid cure under UV, visible, or LED light Making the Joint Work Prepare each surface for its material. Glass is solvent-cleaned and, for humidity durability, plasma-treated or primed with a silane. Metal is degreased and lightly abraded or primed so the adhesive keys into the surface. Choose compliance deliberately. The wider the expansion gap between the specific metal and glass, the more the design benefits from a tougher, higher-elongation grade and a slightly thicker bond line. The mechanism is detailed in how CTE mismatch causes adhesive bond failure. Cure through the glass. Position the fixture so light reaches the bond through the transparent element, and provide a secondary cure route for any part of the joint shadowed by the metal. Control bond-line thickness. Spacers or hard stops keep the gap uniform, which spreads stress evenly and keeps optical path length consistent. For help selecting a metal-to-glass adhesive for a specific pair of materials and temperature range, Email Us with your joint geometry and service conditions. Bond-Line Geometry and Stress Distribution In a glass-to-metal joint, the shear stress from expansion mismatch is not uniform. It is highest at the ends of the bond and near zero in the middle, and the peak rises as the bond gets longer and as the adhesive gets stiffer. Two design levers reduce that peak. The first is bond-line thickness. A thicker layer, within reason, spreads the differential movement over more material and lowers the strain at any point. A very thin…

Comments Off on Bonding Metal to Glass: Selecting a High-Strength Optical Adhesive
August 21, 2024
Optical Adhesives / UV Adhesives / UV Curing Equipments / UV LED Equipments / UV LED Spot Equipments

Optical Adhesives for High-Demand Applications

Some optical assemblies never leave a climate-controlled room. Others ride in a vehicle, sit on a tower, or cycle from freezing to hot every day. When the environment is severe, the adhesive holding the optics has to keep both its alignment and its clarity through conditions that would degrade a general-purpose bond. What "High-Demand" Means for an Optical Bond Demanding service stacks several stresses on the same joint: Thermal cycling between wide temperature extremes, which flexes the bond line every cycle as the substrates expand and contract by different amounts Sustained humidity or damp heat, which can shift refractive index, cloud the layer, or attack the adhesion at the interface Vibration and mechanical shock during transport and operation Long service life, often a decade or more, with no opportunity for rework An adhesive that passes a room-temperature pull test can still fail all of these. Properties That Carry a Bond Through Hard Service Incure formulates the Optik line of light-curable optical adhesives with grades aimed at exactly this problem. The properties that matter for durability are: Low coefficient of thermal expansion and a glass transition temperature above the maximum operating temperature, so the bond stays dimensionally stable and does not soften in heat Very low cure shrinkage, which limits the stress locked into the joint at assembly Low water absorption, keeping index and clarity stable through humidity exposure Toughness and elongation sufficient to absorb vibration and shock without cracking the bond or the glass 100 percent solids chemistry with no volatiles to outgas, form voids, or fog nearby surfaces Rapid, complete cure under UV, visible, or LED light for repeatable production Designing for Durability The single biggest driver of thermal-cycling life is the expansion mismatch between the optic and its mount. A stiff adhesive maximizes alignment stability but transfers that mismatch stress into brittle glass; a more compliant grade absorbs it. The trade-off is explained in how CTE mismatch causes adhesive bond failure, and it should be settled before a grade is chosen. Beyond material selection: Prepare surfaces for humidity resistance. Plasma treatment or a silane primer on glass substantially improves the durability of the interface in damp heat. Control the bond line. A uniform, moderate thickness set by spacers distributes stress better than a thin, variable one. Qualify with real profiles. Subject coupons to the actual temperature range, damp-heat soak, and vibration spectrum the product will see, not a generic screen. For help selecting an optical adhesive for a specific environmental profile, Email Us with your temperature, humidity, and vibration requirements. Outgassing and Enclosed Optical Systems In a sealed optical assembly, anything the adhesive releases as vapor can condense on a cold optic and form a haze that scatters light. Solvent-borne adhesives are the biggest concern here, which is one reason 100 percent solids chemistry is preferred for demanding optical work: there is no carrier solvent to flash off, and a fully cured network has little residual monomer to volatilize. For assemblies destined for vacuum or near-vacuum service, outgassing…

1 Comment
August 21, 2024
Optical Adhesives / UV Adhesives / UV Curing Equipments / UV LED Equipments / UV LED Spot Equipments

Optical Epoxies: Selecting a High-Bond-Strength UV Optical Adhesive

An optical epoxy is asked to be invisible and immovable at the same time. It must transmit light without color or haze, hold precise alignment for years, and carry real mechanical load through shock and temperature swings. Getting all of that from one material means understanding what the specifications actually control. What "Optical" Adds to an Adhesive Spec Beyond ordinary bond strength, an optical adhesive is judged on a second set of properties: Transmission and clarity: High light transmission across the working wavelengths, with low haze and no visible yellowing after cure or aging. Refractive index: A defined index, often near 1.5, so the adhesive layer does not introduce reflection or distortion at the interfaces. Shrinkage: Very low cure shrinkage, because any volume change moves the bonded elements and distorts the wavefront. Coefficient of thermal expansion: A low CTE and a glass transition temperature above the service range keep alignment stable and limit stress on brittle glass. Water absorption: Low uptake, since absorbed moisture shifts index and can cloud the layer. High-Bond-Strength Optical Adhesives Incure formulates the Optik line of light-curable optical adhesives, including grades built for demanding structural optical work. These grades combine strong adhesion to glass and to metal or ceramic mounts with the clarity and dimensional stability an optical path requires. Characteristics typical of the high-strength grades include: Adhesion well into the thousands of psi in lap shear on prepared glass and metal Rapid cure under UV, visible, or LED light, including with low-intensity lamps 100 percent solids formulation with no volatiles to outgas or void Very low shrinkage and low CTE for precise, stable alignment Retention of properties through humidity exposure and thermal cycling Choosing and Using the Right Grade Match viscosity to the joint. A thin, wicking grade fills capillary gaps between mated optics; a thicker grade bridges a defined gap or holds position on a vertical surface. Match mechanical character to the stress. A rigid, high-Tg grade maximizes alignment stability; a slightly more compliant grade better survives the stress of bonding materials with very different expansion rates. The reasons a stiff bond can crack a glass element over temperature are covered in how CTE mismatch causes adhesive bond failure. Prepare surfaces properly. Solvent-clean the glass, and use plasma treatment or a silane primer where long-term humidity resistance is required. Metal mounts should be degreased and lightly abraded or primed. Cure with line of sight to the bond, hold a controlled bond-line thickness with spacers, and manage oxygen inhibition at exposed surfaces with an inert blanket or added dose. For help selecting an optical adhesive grade for a specific assembly, Email Us with your optical, mechanical, and environmental requirements. Testing and Qualification An optical adhesive earns its place in a design by passing tests that mirror service, not a single room-temperature pull. A useful qualification set includes: Lap shear and tensile on the actual substrate pairs, in the surface condition production will use, before and after environmental exposure Thermal cycling across the full operating range,…

1 Comment
August 21, 2024
Optical Adhesives / UV Adhesives / UV Curing Equipments / UV LED Equipments / UV LED Spot Equipments

Glass Bonding Adhesive: Incure Optik 7210 for Clear, Strong Bonds

A glass bond has to do two things that pull against each other: disappear optically and hold mechanically. An adhesive that yellows, shrinks, or stresses the glass distorts a wavefront or cracks a mount long before it fails in shear. Incure Optik 7210 is a low-viscosity, light-curable adhesive for clear, durable glass bonds. What Makes Glass Bonding Difficult Glass is stiff, smooth, and chemically inert, which makes wetting and long-term adhesion harder than on most plastics. It is also brittle, so any stress the adhesive imposes as it cures or as temperature changes goes straight into the glass with no yielding to relieve it. And in an optical path, the cured adhesive is part of the system: its refractive index, clarity, and dimensional stability all affect performance. Where Optik 7210 Fits Optik 7210 cures on demand under UV, visible, or LED light and is built around the needs of optical and glassware assembly: Very low viscosity for precise placement and capillary wicking into thin joints Acid-free, 100 percent solids urethane acrylate chemistry that will not corrode adjacent metals and leaves no volatiles behind Very low linear shrinkage to preserve alignment and minimize wavefront distortion Low water absorption and good thermal and moisture resistance for stable service Toughness and vibration resistance so the bond survives handling and transport VOC-free operation, suitable for enclosed production areas Applying It Well Prepare the glass. Clean with a solvent that leaves no residue, and for demanding service, treat the surface with plasma or an appropriate silane primer to improve durability against humidity. Control the bond line. With a low-viscosity adhesive, the gap is set by the fixture, not the adhesive. Use hard stops or a small fraction of spacer beads to hold a consistent thickness, which keeps index and path length uniform. Cure with line of sight. Light-curable adhesives need the lamp to reach the bond. Design the fixture so glass, not opaque metal, sits between the lamp and the joint, and provide a secondary approach for any shadowed region. Watch for oxygen inhibition. The last few micrometers at an exposed adhesive surface can stay tacky if air contact continues during cure. A nitrogen blanket or a slightly higher dose clears it. Because glass and its mount often expand at very different rates, thermal cycling is where marginal glass bonds fail. Reviewing how expansion mismatch causes bond failure helps in choosing between a stiffer and a more compliant adhesive. The general trade-offs of transparent bonding with UV-curable adhesives apply directly here, and for glass-to-metal joints specifically, matching an adhesive grade to viscosity and tensile requirements is a useful reference. For help evaluating Optik 7210 against your optical and environmental requirements, Email Us with your substrate and joint details. Refractive Index and Optical Performance When an adhesive sits in a light path, its refractive index matters as much as its clarity. If the index is close to that of the glass, light crosses the bonded interface with almost no reflection. If it is significantly different, each…

2 Comments
August 21, 2024
Electronics Adhesives

The FIPG and CIPG Solution for Fast-Paced Production: Incure Uni-Seal 6322

On a high-volume line, a sealing material that needs minutes of oven time or a long moisture cure becomes the bottleneck. Incure Uni-Seal 6322 is a light-curable form-in-place and cure-in-place gasket material designed to seal electronic and automotive housings at the pace of automated production. The Case for Light-Cured Gaskets Traditional gasketing forces a choice between slow-curing liquid sealants and the inventory and fit problems of die-cut parts. A UV, visible, or LED light-curable FIPG or CIPG material removes that trade-off. The bead is dispensed exactly where it is needed, then cured on demand in seconds as the part passes a lamp, so throughput is set by line speed rather than by chemistry. What Uni-Seal 6322 Offers Acid-free formulation that will not corrode copper, solder, or fine-pitch conductors Low viscosity for precise dispensing into narrow channels and around tight corners Fast cure with low-energy LED lamps, suited to inline and conveyorized processes High resilience and memory retention, so the gasket recovers after compression cycles better than many cut elastomers Air-tight sealing against moisture, dust, and pressure differentials Moisture, temperature, and chemical resistance for under-hood and outdoor service Dual use as a temporary mask during conformal coating Building the Process Around It Bead and groove design. Give the dispensed bead a defined cross-section and a target compression of roughly 20 to 40 percent when the housing closes. Consistent geometry is what makes the seal repeatable unit to unit. Dispensing. A positive-displacement dispense head keeps bead volume constant as the material warms or the reservoir drains. Programmed paths hold the bead centered on the flange through corners and changes in direction. Curing. Size the lamp to the largest part so the entire bead reaches full cure in one pass. For long or complex flange paths, an inline conveyor curing system or a correctly matched UV LED flood lamp keeps cure time in step with takt. A cured gasket and a metal or plastic housing expand at different rates, so a seal that is fine at room temperature can loosen in the cold or over-compress when hot. Weighing how thermal expansion mismatch stresses a sealed joint guides the choice between a firmer and a more compliant grade. For help matching Uni-Seal 6322 to a dispense cell and cure station, Email Us with your cycle-time targets and housing geometry. Production Benefits Switching to a light-cured poured gasket typically shortens cycle time, cuts gasket inventory and scrap, reduces rework by forming the seal in one controlled step, and gives engineering the freedom to revise flange geometry without new tooling. The same material can seal a control-unit housing on one line and mask a board for coating on another. Resilience and Compression Set A gasket's job is to keep sealing after it has been compressed, warmed, cooled, and vibrated for years. The property that describes this is compression set: how much permanent deformation remains after the load is removed. A material with high compression set gradually loses its sealing force and the joint starts to leak,…

1 Comment
August 21, 2024
Electronics Adhesives

The FIPG and CIPG Sealing Solution for Electronics and Automotive: Incure Uni-Seal 3393

A poured-in-place gasket only works if it seals on the first try and stays sealed through vibration, temperature swings, and chemical exposure. Cut gaskets shift, compress unevenly, and leave gaps at corners. Incure Uni-Seal 3393 is a light-curable form-in-place and cure-in-place gasket material built to seal complex geometries in electronics and automotive assemblies. Form-in-Place and Cure-in-Place Basics A form-in-place gasket (FIPG) is dispensed as a bead directly onto one mating surface, then cured before assembly so it behaves like a precision-molded seal. A cure-in-place gasket (CIPG) follows the same idea but is compressed between surfaces during cure. Both approaches eliminate gasket inventory, adapt instantly to design changes, and follow irregular flange paths that a die-cut part cannot. Why Uni-Seal 3393 Uni-Seal 3393 cures under UV, visible, or LED light and is engineered around the needs of sensitive electronics: Acid-free chemistry that will not corrode copper, solder, or fine-pitch leads Low viscosity for precise dispensing and penetration into narrow channels Tack-free cure leaving a clean, handleable surface with no residue transfer Air-tight sealing against moisture, dust, and pressure differentials Ease-of-peel rework, so a module can be opened for repair and resealed Moisture, temperature, and chemical resistance for under-hood and outdoor service Dual use as a temporary mask during downstream conformal coating Designing a Reliable Poured Gasket Bead geometry drives the seal. Specify a groove or a defined land width so the dispensed bead has a consistent cross-section and a target compression, generally 20 to 40 percent, when the housing closes. Too little compression leaks; too much extrudes material and can bottom out the joint. Dispense control is the other half. A positive-displacement dispense head holds bead volume constant as the material warms or the reservoir empties, and programmed paths keep the bead centered on the flange around tight corners. After dispensing, the assembly passes under a lamp sized to the part so the entire bead reaches full cure. Because a cured gasket and a metal or plastic housing expand at different rates, a seal that is fine at room temperature can open up in the cold or over-compress when hot. Considering how thermal expansion mismatch stresses a bonded or sealed joint guides the choice between a firmer or a more compliant gasket. Matching the material to a suitable UV LED flood lamp or an inline conveyor system keeps cure time in step with line speed. For help fitting Uni-Seal 3393 to a flange design and dispense process, Email Us with your housing drawings. Poured Gaskets Versus the Alternatives Die-cut elastomer gaskets carry a hidden cost: tooling for each new shape, inventory for each part number, scrap from the cut, and assembly labor to place them without pinching or misaligning. They also seal poorly at tight radii and sharp corners, exactly where enclosures tend to leak. A poured gasket forms to the flange path automatically and needs no part-specific tooling. Room-temperature-vulcanizing (RTV) silicone beads solve the fit problem but cure slowly from the surface inward, so a thick bead can stay soft…

1 Comment
August 21, 2024