{"id":10281,"date":"2025-10-13T22:47:34","date_gmt":"2025-10-13T22:47:34","guid":{"rendered":"https:\/\/incurelab.com\/wp\/?p=10281"},"modified":"2026-08-30T03:24:56","modified_gmt":"2026-08-30T03:24:56","slug":"the-sticky-situation-why-your-uv-resin-cures-tacky-and-how-to-fix-it","status":"publish","type":"post","link":"https:\/\/incurelab.com\/wp\/the-sticky-situation-why-your-uv-resin-cures-tacky-and-how-to-fix-it","title":{"rendered":"The Sticky Situation: Why Your UV Resin Cures Tacky and How to Fix It"},"content":{"rendered":"

You’ve poured, cured, and expected a hard, glassy finish \u2014 instead your light-cured resin is still tacky on the surface. It’s the most common complaint from jewelry makers to industrial prototypers, and it rarely means the resin itself is defective.<\/p>\n

Understanding Oxygen Inhibition<\/h3>\n

This problem, technically called oxygen inhibition, simply means the very top layer of resin didn’t fully polymerize. Light-cured resins harden through free-radical polymerization: UV light activates a photoinitiator in the resin, which generates free radicals that link liquid monomers into a solid polymer chain.<\/p>\n

The complication is oxygen. Atmospheric oxygen at the resin’s surface is a radical scavenger \u2014 it intercepts and neutralizes free radicals before they can complete the polymerization chain. The result is an inhibition layer: a thin, uncured, sticky film on the top surface even while the bulk material underneath cures hard. It’s a normal chemical phenomenon, not a defect, and it’s entirely manageable once you understand the mechanism.<\/p>\n

Practical Solutions to Eliminate the Tacky Surface<\/h3>\n

Wipe it away.<\/strong> For pieces that are fully hard underneath, the fastest fix is wiping the sticky layer off after curing with a soft cloth dampened in isopropyl alcohol (IPA), denatured alcohol, or acetone. IPA is generally the safest choice for the finish \u2014 avoid rubbing too hard, since aggressive scrubbing can dull a high-gloss surface.<\/p>\n

Drown out the oxygen.<\/strong> For a fully cured, non-tacky finish straight from the lamp, block oxygen from reaching the surface during the final cure. Once a piece is roughly 80% cured, submerge it completely in a bowl of clean water and place the whole assembly back under the UV lamp for a final 2\u20133 minute exposure. The water layer acts as an oxygen barrier, letting the surface finish curing completely.<\/p>\n

Apply a top coat.<\/strong> If the surface is mostly hard but only slightly tacky, apply an extremely thin “final flash” layer of the same resin over the tacky area and cure it immediately for a full cycle (around 60 seconds). Because the layer is thin and the oxygen inhibition effect from the layers below is already reduced, this thin coat typically cures fully and becomes the finished, non-tacky surface.<\/p>\n

Upgrade your cure equipment.<\/strong> If tacky finishes are a recurring problem rather than an occasional one, the lamp is often the bottleneck. Low-wattage units \u2014 6W nail lamps and similar \u2014 are frequently insufficient for thicker or pigmented pieces; most professional or hobby-grade resins need 48W to 72W of UV\/LED output to reliably outrun oxygen inhibition. If the lamp is too far away or too weak, the polymerization reaction stalls before completion \u2014 increasing cure time from one minute to four or five minutes, or moving the lamp closer, both help close that gap. Direct, unfiltered sunlight for a few hours provides broad-spectrum UV that can finish a stalled cure as a last resort.<\/p>\n

Watch pigments and thickness.<\/strong> What you add to the resin affects how much UV energy reaches the photoinitiator. Dark pigments \u2014 black, navy, deep red \u2014 and glitter both absorb and block UV penetration, so pieces made with them need thinner layers (under 5mm) and much longer cure times (5\u201310 minutes per side). Some pigments, particularly blues, can also chemically interfere with the photoinitiator; using UV-specific pigment paste designed for resins avoids that interaction entirely.<\/p>\n

Check ambient humidity and temperature.<\/strong> Cold, damp workspaces slow the free-radical reaction at exactly the surface where oxygen inhibition is already working against you, compounding the tacky-finish problem even with an otherwise adequate lamp. A workspace held around 20\u201324\u00b0C with moderate humidity gives the fastest, most complete surface cure; below that range, expect noticeably longer times before the top layer stops feeling wet to the touch, even if the bulk of the piece is already hard underneath.<\/p>\n

Choosing Equipment That Reduces the Problem at the Source<\/h3>\n

Rather than compensating for a weak lamp after the fact, matching lamp intensity to the resin’s photoinitiator wavelength up front eliminates most tacky-finish complaints before they start. Reviewing options like an industrial UV spot lamp built around lightguide reach and working distance<\/a> is a useful next step if you’re regularly fighting oxygen inhibition on pigmented or thicker pieces. For glass or optical substrates specifically, it’s also worth comparing UV glue versus epoxy for transparent bonding<\/a> since the two chemistries handle surface tack very differently.<\/p>\n

If you’re seeing persistent tackiness across a production run and want help diagnosing whether it’s a lamp, pigment, or technique issue, Email Us<\/a> with your resin type and cure setup.<\/p>\n

By applying one or more of these techniques, you can consistently achieve a hard, durable, completely non-tacky finish on light-cured resin projects. Contact Our Team<\/a> if you’d like help selecting a curing lamp matched to your specific resin and substrate.<\/p>\n

Visit www.incurelab.com<\/a> for more information.<\/p>\n","protected":false},"excerpt":{"rendered":"

You’ve poured, cured, and expected a hard, glassy finish \u2014 instead your light-cured resin is still tacky on the surface. It’s the most common complaint from jewelry makers to industrial prototypers, and it rarely means the resin itself is defective. Understanding Oxygen Inhibition This problem, technically called oxygen inhibition, simply means the very top layer […]<\/p>\n","protected":false},"author":9,"featured_media":0,"comment_status":"closed","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"ocean_front_end_style_editor":"no","ocean_post_layout":"","ocean_both_sidebars_style":"","ocean_both_sidebars_content_width":0,"ocean_both_sidebars_sidebars_width":0,"ocean_sidebar":"","ocean_second_sidebar":"","ocean_disable_margins":"enable","ocean_add_body_class":"","ocean_shortcode_before_top_bar":"","ocean_shortcode_after_top_bar":"","ocean_shortcode_before_header":"","ocean_shortcode_after_header":"","ocean_has_shortcode":"","ocean_shortcode_after_title":"","ocean_shortcode_before_footer_widgets":"","ocean_shortcode_after_footer_widgets":"","ocean_shortcode_before_footer_bottom":"","ocean_shortcode_after_footer_bottom":"","ocean_display_top_bar":"default","ocean_display_header":"default","ocean_header_style":"","ocean_center_header_left_menu":"","ocean_custom_header_template":"","ocean_custom_logo":0,"ocean_custom_retina_logo":0,"ocean_custom_logo_max_width":0,"ocean_custom_logo_tablet_max_width":0,"ocean_custom_logo_mobile_max_width":0,"ocean_custom_logo_max_height":0,"ocean_custom_logo_tablet_max_height":0,"ocean_custom_logo_mobile_max_height":0,"ocean_header_custom_menu":"","ocean_menu_typo_font_family":"","ocean_menu_typo_font_subset":"","ocean_menu_typo_font_size":0,"ocean_menu_typo_font_size_tablet":0,"ocean_menu_typo_font_size_mobile":0,"ocean_menu_typo_font_size_unit":"px","ocean_menu_typo_font_weight":"","ocean_menu_typo_font_weight_tablet":"","ocean_menu_typo_font_weight_mobile":"","ocean_menu_typo_transform":"","ocean_menu_typo_transform_tablet":"","ocean_menu_typo_transform_mobile":"","ocean_menu_typo_line_height":0,"ocean_menu_typo_line_height_tablet":0,"ocean_menu_typo_line_height_mobile":0,"ocean_menu_typo_line_height_unit":"","ocean_menu_typo_spacing":0,"ocean_menu_typo_spacing_tablet":0,"ocean_menu_typo_spacing_mobile":0,"ocean_menu_typo_spacing_unit":"","ocean_menu_link_color":"","ocean_menu_link_color_hover":"","ocean_menu_link_color_active":"","ocean_menu_link_background":"","ocean_menu_link_hover_background":"","ocean_menu_link_active_background":"","ocean_menu_social_links_bg":"","ocean_menu_social_hover_links_bg":"","ocean_menu_social_links_color":"","ocean_menu_social_hover_links_color":"","ocean_disable_title":"default","ocean_disable_heading":"default","ocean_post_title":"","ocean_post_subheading":"","ocean_post_title_style":"","ocean_post_title_background_color":"","ocean_post_title_background":0,"ocean_post_title_bg_image_position":"","ocean_post_title_bg_image_attachment":"","ocean_post_title_bg_image_repeat":"","ocean_post_title_bg_image_size":"","ocean_post_title_height":0,"ocean_post_title_bg_overlay":0.5,"ocean_post_title_bg_overlay_color":"","ocean_disable_breadcrumbs":"default","ocean_breadcrumbs_color":"","ocean_breadcrumbs_separator_color":"","ocean_breadcrumbs_links_color":"","ocean_breadcrumbs_links_hover_color":"","ocean_display_footer_widgets":"default","ocean_display_footer_bottom":"default","ocean_custom_footer_template":"","ocean_post_oembed":"","ocean_post_self_hosted_media":"","ocean_post_video_embed":"","ocean_link_format":"","ocean_link_format_target":"self","ocean_quote_format":"","ocean_quote_format_link":"post","ocean_gallery_link_images":"on","ocean_gallery_id":[],"footnotes":""},"categories":[1],"tags":[],"class_list":["post-10281","post","type-post","status-publish","format-standard","hentry","category-uncategorized","entry"],"yoast_head":"\nThe Sticky Situation: Why Your UV Resin Cures Tacky and How to Fix It - INCURE INC.<\/title>\n<meta name=\"robots\" content=\"index, follow, max-snippet:-1, max-image-preview:large, max-video-preview:-1\" \/>\n<link rel=\"canonical\" href=\"https:\/\/incurelab.com\/wp\/the-sticky-situation-why-your-uv-resin-cures-tacky-and-how-to-fix-it\" \/>\n<meta property=\"og:locale\" content=\"en_US\" \/>\n<meta property=\"og:type\" content=\"article\" \/>\n<meta property=\"og:title\" content=\"The Sticky Situation: Why Your UV Resin Cures Tacky and How to Fix It - INCURE INC.\" \/>\n<meta property=\"og:description\" content=\"You’ve poured, cured, and expected a hard, glassy finish \u2014 instead your light-cured resin is still tacky on the surface. It’s the most common complaint from jewelry makers to industrial prototypers, and it rarely means the resin itself is defective. Understanding Oxygen Inhibition This problem, technically called oxygen inhibition, simply means the very top layer […]\" \/>\n<meta property=\"og:url\" content=\"https:\/\/incurelab.com\/wp\/the-sticky-situation-why-your-uv-resin-cures-tacky-and-how-to-fix-it\" \/>\n<meta property=\"og:site_name\" content=\"INCURE INC.\" \/>\n<meta property=\"article:published_time\" content=\"2025-10-13T22:47:34+00:00\" \/>\n<meta property=\"article:modified_time\" content=\"2026-08-30T03:24:56+00:00\" \/>\n<meta name=\"author\" content=\"Incure Content Team\" \/>\n<meta name=\"twitter:card\" content=\"summary_large_image\" \/>\n<meta name=\"twitter:label1\" content=\"Written by\" \/>\n\t<meta name=\"twitter:data1\" content=\"Incure Content Team\" \/>\n\t<meta name=\"twitter:label2\" content=\"Est. reading time\" \/>\n\t<meta name=\"twitter:data2\" content=\"4 minutes\" \/>\n<script type=\"application\/ld+json\" class=\"yoast-schema-graph\">{\"@context\":\"https:\\\/\\\/schema.org\",\"@graph\":[{\"@type\":\"Article\",\"@id\":\"https:\\\/\\\/incurelab.com\\\/wp\\\/the-sticky-situation-why-your-uv-resin-cures-tacky-and-how-to-fix-it#article\",\"isPartOf\":{\"@id\":\"https:\\\/\\\/incurelab.com\\\/wp\\\/the-sticky-situation-why-your-uv-resin-cures-tacky-and-how-to-fix-it\"},\"author\":{\"name\":\"Incure Content Team\",\"@id\":\"https:\\\/\\\/incurelab.com\\\/wp\\\/#\\\/schema\\\/person\\\/53482b163015e8f48dc86f4132515727\"},\"headline\":\"The Sticky Situation: Why Your UV Resin Cures Tacky and How to Fix It\",\"datePublished\":\"2025-10-13T22:47:34+00:00\",\"dateModified\":\"2026-08-30T03:24:56+00:00\",\"mainEntityOfPage\":{\"@id\":\"https:\\\/\\\/incurelab.com\\\/wp\\\/the-sticky-situation-why-your-uv-resin-cures-tacky-and-how-to-fix-it\"},\"wordCount\":808,\"publisher\":{\"@id\":\"https:\\\/\\\/incurelab.com\\\/wp\\\/#organization\"},\"inLanguage\":\"en-US\"},{\"@type\":\"WebPage\",\"@id\":\"https:\\\/\\\/incurelab.com\\\/wp\\\/the-sticky-situation-why-your-uv-resin-cures-tacky-and-how-to-fix-it\",\"url\":\"https:\\\/\\\/incurelab.com\\\/wp\\\/the-sticky-situation-why-your-uv-resin-cures-tacky-and-how-to-fix-it\",\"name\":\"The Sticky Situation: Why Your UV Resin Cures Tacky and How to Fix It - INCURE INC.\",\"isPartOf\":{\"@id\":\"https:\\\/\\\/incurelab.com\\\/wp\\\/#website\"},\"datePublished\":\"2025-10-13T22:47:34+00:00\",\"dateModified\":\"2026-08-30T03:24:56+00:00\",\"breadcrumb\":{\"@id\":\"https:\\\/\\\/incurelab.com\\\/wp\\\/the-sticky-situation-why-your-uv-resin-cures-tacky-and-how-to-fix-it#breadcrumb\"},\"inLanguage\":\"en-US\",\"potentialAction\":[{\"@type\":\"ReadAction\",\"target\":[\"https:\\\/\\\/incurelab.com\\\/wp\\\/the-sticky-situation-why-your-uv-resin-cures-tacky-and-how-to-fix-it\"]}]},{\"@type\":\"BreadcrumbList\",\"@id\":\"https:\\\/\\\/incurelab.com\\\/wp\\\/the-sticky-situation-why-your-uv-resin-cures-tacky-and-how-to-fix-it#breadcrumb\",\"itemListElement\":[{\"@type\":\"ListItem\",\"position\":1,\"name\":\"Home\",\"item\":\"https:\\\/\\\/incurelab.com\\\/wp\\\/\"},{\"@type\":\"ListItem\",\"position\":2,\"name\":\"The Sticky Situation: Why Your UV Resin Cures Tacky and How to Fix It\"}]},{\"@type\":\"WebSite\",\"@id\":\"https:\\\/\\\/incurelab.com\\\/wp\\\/#website\",\"url\":\"https:\\\/\\\/incurelab.com\\\/wp\\\/\",\"name\":\"INCURE INC.\",\"description\":\"Engineered Solutions. Trusted Worldwide\",\"publisher\":{\"@id\":\"https:\\\/\\\/incurelab.com\\\/wp\\\/#organization\"},\"potentialAction\":[{\"@type\":\"SearchAction\",\"target\":{\"@type\":\"EntryPoint\",\"urlTemplate\":\"https:\\\/\\\/incurelab.com\\\/wp\\\/?s={search_term_string}\"},\"query-input\":{\"@type\":\"PropertyValueSpecification\",\"valueRequired\":true,\"valueName\":\"search_term_string\"}}],\"inLanguage\":\"en-US\"},{\"@type\":\"Organization\",\"@id\":\"https:\\\/\\\/incurelab.com\\\/wp\\\/#organization\",\"name\":\"INCURE INC.\",\"url\":\"https:\\\/\\\/incurelab.com\\\/wp\\\/\",\"logo\":{\"@type\":\"ImageObject\",\"inLanguage\":\"en-US\",\"@id\":\"https:\\\/\\\/incurelab.com\\\/wp\\\/#\\\/schema\\\/logo\\\/image\\\/\",\"url\":\"https:\\\/\\\/incurelab.com\\\/wp\\\/wp-content\\\/uploads\\\/2025\\\/07\\\/incure-logo.jpeg\",\"contentUrl\":\"https:\\\/\\\/incurelab.com\\\/wp\\\/wp-content\\\/uploads\\\/2025\\\/07\\\/incure-logo.jpeg\",\"width\":164,\"height\":45,\"caption\":\"INCURE INC.\"},\"image\":{\"@id\":\"https:\\\/\\\/incurelab.com\\\/wp\\\/#\\\/schema\\\/logo\\\/image\\\/\"}},{\"@type\":\"Person\",\"@id\":\"https:\\\/\\\/incurelab.com\\\/wp\\\/#\\\/schema\\\/person\\\/53482b163015e8f48dc86f4132515727\",\"name\":\"Incure Content Team\",\"image\":{\"@type\":\"ImageObject\",\"inLanguage\":\"en-US\",\"@id\":\"https:\\\/\\\/secure.gravatar.com\\\/avatar\\\/85e856c6e17c9c44477ea1e0964ef5dc19c2a1ef29a741bb9bb742fcfc644fcc?s=96&d=mm&r=g\",\"url\":\"https:\\\/\\\/secure.gravatar.com\\\/avatar\\\/85e856c6e17c9c44477ea1e0964ef5dc19c2a1ef29a741bb9bb742fcfc644fcc?s=96&d=mm&r=g\",\"contentUrl\":\"https:\\\/\\\/secure.gravatar.com\\\/avatar\\\/85e856c6e17c9c44477ea1e0964ef5dc19c2a1ef29a741bb9bb742fcfc644fcc?s=96&d=mm&r=g\",\"caption\":\"Incure Content Team\"},\"url\":\"https:\\\/\\\/incurelab.com\\\/wp\\\/author\\\/kimleelcy\"}]}<\/script>\n<!-- \/ Yoast SEO plugin. -->","yoast_head_json":{"title":"The Sticky Situation: Why Your UV Resin Cures Tacky and How to Fix It - INCURE INC.","robots":{"index":"index","follow":"follow","max-snippet":"max-snippet:-1","max-image-preview":"max-image-preview:large","max-video-preview":"max-video-preview:-1"},"canonical":"https:\/\/incurelab.com\/wp\/the-sticky-situation-why-your-uv-resin-cures-tacky-and-how-to-fix-it","og_locale":"en_US","og_type":"article","og_title":"The Sticky Situation: Why Your UV Resin Cures Tacky and How to Fix It - INCURE INC.","og_description":"You’ve poured, cured, and expected a hard, glassy finish \u2014 instead your light-cured resin is still tacky on the surface. It’s the most common complaint from jewelry makers to industrial prototypers, and it rarely means the resin itself is defective. Understanding Oxygen Inhibition This problem, technically called oxygen inhibition, simply means the very top layer […]","og_url":"https:\/\/incurelab.com\/wp\/the-sticky-situation-why-your-uv-resin-cures-tacky-and-how-to-fix-it","og_site_name":"INCURE INC.","article_published_time":"2025-10-13T22:47:34+00:00","article_modified_time":"2026-08-30T03:24:56+00:00","author":"Incure Content Team","twitter_card":"summary_large_image","twitter_misc":{"Written by":"Incure Content Team","Est. reading time":"4 minutes"},"schema":{"@context":"https:\/\/schema.org","@graph":[{"@type":"Article","@id":"https:\/\/incurelab.com\/wp\/the-sticky-situation-why-your-uv-resin-cures-tacky-and-how-to-fix-it#article","isPartOf":{"@id":"https:\/\/incurelab.com\/wp\/the-sticky-situation-why-your-uv-resin-cures-tacky-and-how-to-fix-it"},"author":{"name":"Incure Content Team","@id":"https:\/\/incurelab.com\/wp\/#\/schema\/person\/53482b163015e8f48dc86f4132515727"},"headline":"The Sticky Situation: Why Your UV Resin Cures Tacky and How to Fix It","datePublished":"2025-10-13T22:47:34+00:00","dateModified":"2026-08-30T03:24:56+00:00","mainEntityOfPage":{"@id":"https:\/\/incurelab.com\/wp\/the-sticky-situation-why-your-uv-resin-cures-tacky-and-how-to-fix-it"},"wordCount":808,"publisher":{"@id":"https:\/\/incurelab.com\/wp\/#organization"},"inLanguage":"en-US"},{"@type":"WebPage","@id":"https:\/\/incurelab.com\/wp\/the-sticky-situation-why-your-uv-resin-cures-tacky-and-how-to-fix-it","url":"https:\/\/incurelab.com\/wp\/the-sticky-situation-why-your-uv-resin-cures-tacky-and-how-to-fix-it","name":"The Sticky Situation: Why Your UV Resin Cures Tacky and How to Fix It - INCURE INC.","isPartOf":{"@id":"https:\/\/incurelab.com\/wp\/#website"},"datePublished":"2025-10-13T22:47:34+00:00","dateModified":"2026-08-30T03:24:56+00:00","breadcrumb":{"@id":"https:\/\/incurelab.com\/wp\/the-sticky-situation-why-your-uv-resin-cures-tacky-and-how-to-fix-it#breadcrumb"},"inLanguage":"en-US","potentialAction":[{"@type":"ReadAction","target":["https:\/\/incurelab.com\/wp\/the-sticky-situation-why-your-uv-resin-cures-tacky-and-how-to-fix-it"]}]},{"@type":"BreadcrumbList","@id":"https:\/\/incurelab.com\/wp\/the-sticky-situation-why-your-uv-resin-cures-tacky-and-how-to-fix-it#breadcrumb","itemListElement":[{"@type":"ListItem","position":1,"name":"Home","item":"https:\/\/incurelab.com\/wp\/"},{"@type":"ListItem","position":2,"name":"The Sticky Situation: Why Your UV Resin Cures Tacky and How to Fix It"}]},{"@type":"WebSite","@id":"https:\/\/incurelab.com\/wp\/#website","url":"https:\/\/incurelab.com\/wp\/","name":"INCURE INC.","description":"Engineered Solutions. Trusted Worldwide","publisher":{"@id":"https:\/\/incurelab.com\/wp\/#organization"},"potentialAction":[{"@type":"SearchAction","target":{"@type":"EntryPoint","urlTemplate":"https:\/\/incurelab.com\/wp\/?s={search_term_string}"},"query-input":{"@type":"PropertyValueSpecification","valueRequired":true,"valueName":"search_term_string"}}],"inLanguage":"en-US"},{"@type":"Organization","@id":"https:\/\/incurelab.com\/wp\/#organization","name":"INCURE INC.","url":"https:\/\/incurelab.com\/wp\/","logo":{"@type":"ImageObject","inLanguage":"en-US","@id":"https:\/\/incurelab.com\/wp\/#\/schema\/logo\/image\/","url":"https:\/\/incurelab.com\/wp\/wp-content\/uploads\/2025\/07\/incure-logo.jpeg","contentUrl":"https:\/\/incurelab.com\/wp\/wp-content\/uploads\/2025\/07\/incure-logo.jpeg","width":164,"height":45,"caption":"INCURE INC."},"image":{"@id":"https:\/\/incurelab.com\/wp\/#\/schema\/logo\/image\/"}},{"@type":"Person","@id":"https:\/\/incurelab.com\/wp\/#\/schema\/person\/53482b163015e8f48dc86f4132515727","name":"Incure Content Team","image":{"@type":"ImageObject","inLanguage":"en-US","@id":"https:\/\/secure.gravatar.com\/avatar\/85e856c6e17c9c44477ea1e0964ef5dc19c2a1ef29a741bb9bb742fcfc644fcc?s=96&d=mm&r=g","url":"https:\/\/secure.gravatar.com\/avatar\/85e856c6e17c9c44477ea1e0964ef5dc19c2a1ef29a741bb9bb742fcfc644fcc?s=96&d=mm&r=g","contentUrl":"https:\/\/secure.gravatar.com\/avatar\/85e856c6e17c9c44477ea1e0964ef5dc19c2a1ef29a741bb9bb742fcfc644fcc?s=96&d=mm&r=g","caption":"Incure Content Team"},"url":"https:\/\/incurelab.com\/wp\/author\/kimleelcy"}]}},"rttpg_featured_image_url":null,"rttpg_author":{"display_name":"Incure Content Team","author_link":"https:\/\/incurelab.com\/wp\/author\/kimleelcy"},"rttpg_comment":0,"rttpg_category":"<a href=\"https:\/\/incurelab.com\/wp\/category\/uncategorized\" rel=\"category tag\">Uncategorized<\/a>","rttpg_excerpt":"You’ve poured, cured, and expected a hard, glassy finish \u2014 instead your light-cured resin is still tacky on the surface. It’s the most common complaint from jewelry makers to industrial prototypers, and it rarely means the resin itself is defective. Understanding Oxygen Inhibition This problem, technically called oxygen inhibition, simply means the very top layer…","_links":{"self":[{"href":"https:\/\/incurelab.com\/wp\/wp-json\/wp\/v2\/posts\/10281","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/incurelab.com\/wp\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/incurelab.com\/wp\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/incurelab.com\/wp\/wp-json\/wp\/v2\/users\/9"}],"replies":[{"embeddable":true,"href":"https:\/\/incurelab.com\/wp\/wp-json\/wp\/v2\/comments?post=10281"}],"version-history":[{"count":3,"href":"https:\/\/incurelab.com\/wp\/wp-json\/wp\/v2\/posts\/10281\/revisions"}],"predecessor-version":[{"id":22687,"href":"https:\/\/incurelab.com\/wp\/wp-json\/wp\/v2\/posts\/10281\/revisions\/22687"}],"wp:attachment":[{"href":"https:\/\/incurelab.com\/wp\/wp-json\/wp\/v2\/media?parent=10281"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/incurelab.com\/wp\/wp-json\/wp\/v2\/categories?post=10281"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/incurelab.com\/wp\/wp-json\/wp\/v2\/tags?post=10281"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}