{"id":14243,"date":"2026-01-07T13:10:58","date_gmt":"2026-01-07T13:10:58","guid":{"rendered":"https:\/\/incurelab.com\/wp\/how-to-prevent-bubbles-in-uv-resin-the-ultimate-guide"},"modified":"2026-09-12T00:43:01","modified_gmt":"2026-09-12T00:43:01","slug":"how-to-prevent-bubbles-in-uv-resin-the-ultimate-guide","status":"publish","type":"post","link":"https:\/\/incurelab.com\/wp\/how-to-prevent-bubbles-in-uv-resin-the-ultimate-guide","title":{"rendered":"UV Resin Bubbles: A Symptom-by-Symptom Diagnostic Guide"},"content":{"rendered":"

Not every bubble defect in cured UV resin has the same cause, and treating them all with the same fix \u2014 usually “add more vacuum degassing” \u2014 wastes process time on defects that vacuum degassing was never going to solve in the first place.<\/p>\n

Symptom: Fine Pinholes Scattered Across the Surface<\/h3>\n

Surface pinholes, distinct from larger subsurface voids, usually trace back to rapid surface-layer curing trapping volatile byproducts underneath \u2014 sometimes called skinning. If the UV intensity is high enough to cure the top layer before entrained gas has a chance to escape, that gas gets sealed in as a fine pinhole pattern rather than a single large void. A stepped cure profile \u2014 a brief lower-intensity “gel” exposure before the final high-intensity cure \u2014 gives trapped gas time to escape before the surface locks solid, and usually eliminates this specific symptom without any change to the resin formulation itself.<\/p>\n

Symptom: A Small Number of Large, Isolated Subsurface Voids<\/h3>\n

Large, isolated voids rather than a fine scattered pattern usually point back to mechanical air entrapment during dispensing rather than a curing-process issue. A blunt dispensing tip, excessive drop height between the needle and the substrate, or turbulent flow through a jetting valve all fold discrete pockets of air into the resin during application, well before any UV exposure happens. Switching to a tapered dispensing tip, minimizing drop height, and keeping the needle close to the substrate during a continuous bead application typically resolves this pattern specifically, without needing to touch degassing parameters at all.<\/p>\n

Symptom: Bubbles Concentrated Specifically at the Substrate Interface<\/h3>\n

Bubbles that show up right at the resin-substrate boundary, rather than distributed through the bulk material, usually indicate a wetting failure rather than an air-entrapment or curing problem. If the substrate’s surface energy is lower than the resin’s surface tension, the resin doesn’t spread fully into microscopic surface valleys, and air gets trapped in those valleys at the interface. Plasma or corona treatment to raise surface energy, rather than any change to degassing or dispensing technique, is the correct fix for this specific pattern \u2014 applying more vacuum degassing to a wetting problem won’t help, since the air is being trapped at the moment of contact, not carried in with the bulk resin.<\/p>\n

Symptom: Bubbles That Only Appear in High-Viscosity Formulations, Never in Low-Viscosity Ones<\/h3>\n

This is a straightforward degassing-capacity problem. Low-viscosity resins allow entrained air to rise and escape naturally under gravity alone; high-viscosity, thixotropic formulations resist that natural rise, so mechanical intervention \u2014 vacuum degassing chambers or planetary centrifugal mixing at meaningful G-force \u2014 becomes necessary specifically for the higher-viscosity end of a product line. Email Us<\/a> if you’re seeing this pattern and want help sizing a degassing step to a specific formulation’s viscosity range.<\/p>\n

Symptom: Bubbles That Appear Intermittently, Not on Every Unit<\/h3>\n

Intermittent rather than consistent bubble defects usually point to a process-control gap rather than a fundamental material or equipment problem \u2014 inconsistent operator technique on a manually dispensed line, ambient humidity swings affecting outgassing from a porous substrate, or dispensing equipment that isn’t holding a consistent volume shot to shot. Isolating an intermittent defect requires tracking which specific shift, operator, or equipment station produced the affected units, rather than assuming the formulation itself is unreliable.<\/p>\n

Applications Where Bubble Diagnosis Matters Most<\/h3>\n

Renewable energy sensor encapsulation.<\/strong> Outdoor sensor housings potted with UV resin see years of thermal cycling, and a void that seemed cosmetic at assembly can become a moisture-ingress pathway that shortens field service life meaningfully below its rated design.<\/p>\n

Marine instrument potting.<\/strong> Navigation and communication equipment housings combine humidity, salt exposure, and vibration; a subsurface void in a potted assembly here is a corrosion initiation point waiting for enough time in service to matter, not just an aesthetic flaw.<\/p>\n

Verifying the Fix Actually Worked<\/h3>\n

After applying a symptom-specific fix, confirming it worked requires more than a visual check on the next unit off the line \u2014 a small sample run examined under magnification, or cross-sectioned on a periodic basis, catches subsurface voids that a surface inspection alone would miss. For matching UV lamp output to the resin’s photoinitiator package, which affects cure-profile-related bubble symptoms specifically, Incure’s L-Series\u2122 UV LED flood lamp guide<\/a> is a useful reference, and what causes UV light guide degradation over time<\/a> covers a related maintenance concern for systems using fiber-optic or liquid light-guide delivery. Incure’s broader guide to preventing bubbles in UV resin<\/a> covers the underlying degassing and dispensing fundamentals this symptom-based approach builds on.<\/p>\n

Matching the fix to the actual symptom \u2014 rather than defaulting to more degassing for every bubble complaint \u2014 is what gets a production line back to a void-free process without wasted process changes. Contact Our Team<\/a> to walk through a specific bubble defect pattern with our applications team.<\/p>\n

Visit www.incurelab.com<\/a> for more information.<\/p>\n","protected":false},"excerpt":{"rendered":"

Not every bubble defect in cured UV resin has the same cause, and treating them all with the same fix \u2014 usually “add more vacuum degassing” \u2014 wastes process time on defects that vacuum degassing was never going to solve in the first place. Symptom: Fine Pinholes Scattered Across the Surface Surface pinholes, distinct from […]<\/p>\n","protected":false},"author":9,"featured_media":0,"comment_status":"closed","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"ocean_front_end_style_editor":"no","ocean_post_layout":"","ocean_both_sidebars_style":"","ocean_both_sidebars_content_width":0,"ocean_both_sidebars_sidebars_width":0,"ocean_sidebar":"","ocean_second_sidebar":"","ocean_disable_margins":"enable","ocean_add_body_class":"","ocean_shortcode_before_top_bar":"","ocean_shortcode_after_top_bar":"","ocean_shortcode_before_header":"","ocean_shortcode_after_header":"","ocean_has_shortcode":"","ocean_shortcode_after_title":"","ocean_shortcode_before_footer_widgets":"","ocean_shortcode_after_footer_widgets":"","ocean_shortcode_before_footer_bottom":"","ocean_shortcode_after_footer_bottom":"","ocean_display_top_bar":"default","ocean_display_header":"default","ocean_header_style":"","ocean_center_header_left_menu":"","ocean_custom_header_template":"","ocean_custom_logo":0,"ocean_custom_retina_logo":0,"ocean_custom_logo_max_width":0,"ocean_custom_logo_tablet_max_width":0,"ocean_custom_logo_mobile_max_width":0,"ocean_custom_logo_max_height":0,"ocean_custom_logo_tablet_max_height":0,"ocean_custom_logo_mobile_max_height":0,"ocean_header_custom_menu":"","ocean_menu_typo_font_family":"","ocean_menu_typo_font_subset":"","ocean_menu_typo_font_size":0,"ocean_menu_typo_font_size_tablet":0,"ocean_menu_typo_font_size_mobile":0,"ocean_menu_typo_font_size_unit":"px","ocean_menu_typo_font_weight":"","ocean_menu_typo_font_weight_tablet":"","ocean_menu_typo_font_weight_mobile":"","ocean_menu_typo_transform":"","ocean_menu_typo_transform_tablet":"","ocean_menu_typo_transform_mobile":"","ocean_menu_typo_line_height":0,"ocean_menu_typo_line_height_tablet":0,"ocean_menu_typo_line_height_mobile":0,"ocean_menu_typo_line_height_unit":"","ocean_menu_typo_spacing":0,"ocean_menu_typo_spacing_tablet":0,"ocean_menu_typo_spacing_mobile":0,"ocean_menu_typo_spacing_unit":"","ocean_menu_link_color":"","ocean_menu_link_color_hover":"","ocean_menu_link_color_active":"","ocean_menu_link_background":"","ocean_menu_link_hover_background":"","ocean_menu_link_active_background":"","ocean_menu_social_links_bg":"","ocean_menu_social_hover_links_bg":"","ocean_menu_social_links_color":"","ocean_menu_social_hover_links_color":"","ocean_disable_title":"default","ocean_disable_heading":"default","ocean_post_title":"","ocean_post_subheading":"","ocean_post_title_style":"","ocean_post_title_background_color":"","ocean_post_title_background":0,"ocean_post_title_bg_image_position":"","ocean_post_title_bg_image_attachment":"","ocean_post_title_bg_image_repeat":"","ocean_post_title_bg_image_size":"","ocean_post_title_height":0,"ocean_post_title_bg_overlay":0.5,"ocean_post_title_bg_overlay_color":"","ocean_disable_breadcrumbs":"default","ocean_breadcrumbs_color":"","ocean_breadcrumbs_separator_color":"","ocean_breadcrumbs_links_color":"","ocean_breadcrumbs_links_hover_color":"","ocean_display_footer_widgets":"default","ocean_display_footer_bottom":"default","ocean_custom_footer_template":"","ocean_post_oembed":"","ocean_post_self_hosted_media":"","ocean_post_video_embed":"","ocean_link_format":"","ocean_link_format_target":"self","ocean_quote_format":"","ocean_quote_format_link":"post","ocean_gallery_link_images":"on","ocean_gallery_id":[],"footnotes":""},"categories":[1],"tags":[],"class_list":["post-14243","post","type-post","status-publish","format-standard","hentry","category-uncategorized","entry"],"yoast_head":"\nUV Resin Bubbles: A Symptom-by-Symptom Diagnostic Guide - INCURE INC.<\/title>\n<meta name=\"robots\" content=\"index, follow, max-snippet:-1, max-image-preview:large, max-video-preview:-1\" \/>\n<link rel=\"canonical\" href=\"https:\/\/incurelab.com\/wp\/how-to-prevent-bubbles-in-uv-resin-the-ultimate-guide\" \/>\n<meta property=\"og:locale\" content=\"en_US\" \/>\n<meta property=\"og:type\" content=\"article\" \/>\n<meta property=\"og:title\" content=\"UV Resin Bubbles: A Symptom-by-Symptom Diagnostic Guide - INCURE INC.\" \/>\n<meta property=\"og:description\" content=\"Not every bubble defect in cured UV resin has the same cause, and treating them all with the same fix \u2014 usually “add more vacuum degassing” \u2014 wastes process time on defects that vacuum degassing was never going to solve in the first place. Symptom: Fine Pinholes Scattered Across the Surface Surface pinholes, distinct from […]\" \/>\n<meta property=\"og:url\" content=\"https:\/\/incurelab.com\/wp\/how-to-prevent-bubbles-in-uv-resin-the-ultimate-guide\" \/>\n<meta property=\"og:site_name\" content=\"INCURE INC.\" \/>\n<meta property=\"article:published_time\" content=\"2026-01-07T13:10:58+00:00\" \/>\n<meta property=\"article:modified_time\" content=\"2026-09-12T00:43:01+00:00\" \/>\n<meta name=\"author\" content=\"Incure Content Team\" \/>\n<meta name=\"twitter:card\" content=\"summary_large_image\" \/>\n<meta name=\"twitter:label1\" content=\"Written by\" \/>\n\t<meta name=\"twitter:data1\" content=\"Incure Content Team\" \/>\n\t<meta name=\"twitter:label2\" content=\"Est. reading time\" \/>\n\t<meta name=\"twitter:data2\" content=\"4 minutes\" \/>\n<script type=\"application\/ld+json\" class=\"yoast-schema-graph\">{\"@context\":\"https:\\\/\\\/schema.org\",\"@graph\":[{\"@type\":\"Article\",\"@id\":\"https:\\\/\\\/incurelab.com\\\/wp\\\/how-to-prevent-bubbles-in-uv-resin-the-ultimate-guide#article\",\"isPartOf\":{\"@id\":\"https:\\\/\\\/incurelab.com\\\/wp\\\/how-to-prevent-bubbles-in-uv-resin-the-ultimate-guide\"},\"author\":{\"name\":\"Incure Content Team\",\"@id\":\"https:\\\/\\\/incurelab.com\\\/wp\\\/#\\\/schema\\\/person\\\/53482b163015e8f48dc86f4132515727\"},\"headline\":\"UV Resin Bubbles: A Symptom-by-Symptom Diagnostic Guide\",\"datePublished\":\"2026-01-07T13:10:58+00:00\",\"dateModified\":\"2026-09-12T00:43:01+00:00\",\"mainEntityOfPage\":{\"@id\":\"https:\\\/\\\/incurelab.com\\\/wp\\\/how-to-prevent-bubbles-in-uv-resin-the-ultimate-guide\"},\"wordCount\":809,\"publisher\":{\"@id\":\"https:\\\/\\\/incurelab.com\\\/wp\\\/#organization\"},\"inLanguage\":\"en-US\"},{\"@type\":\"WebPage\",\"@id\":\"https:\\\/\\\/incurelab.com\\\/wp\\\/how-to-prevent-bubbles-in-uv-resin-the-ultimate-guide\",\"url\":\"https:\\\/\\\/incurelab.com\\\/wp\\\/how-to-prevent-bubbles-in-uv-resin-the-ultimate-guide\",\"name\":\"UV Resin Bubbles: A Symptom-by-Symptom Diagnostic Guide - INCURE INC.\",\"isPartOf\":{\"@id\":\"https:\\\/\\\/incurelab.com\\\/wp\\\/#website\"},\"datePublished\":\"2026-01-07T13:10:58+00:00\",\"dateModified\":\"2026-09-12T00:43:01+00:00\",\"breadcrumb\":{\"@id\":\"https:\\\/\\\/incurelab.com\\\/wp\\\/how-to-prevent-bubbles-in-uv-resin-the-ultimate-guide#breadcrumb\"},\"inLanguage\":\"en-US\",\"potentialAction\":[{\"@type\":\"ReadAction\",\"target\":[\"https:\\\/\\\/incurelab.com\\\/wp\\\/how-to-prevent-bubbles-in-uv-resin-the-ultimate-guide\"]}]},{\"@type\":\"BreadcrumbList\",\"@id\":\"https:\\\/\\\/incurelab.com\\\/wp\\\/how-to-prevent-bubbles-in-uv-resin-the-ultimate-guide#breadcrumb\",\"itemListElement\":[{\"@type\":\"ListItem\",\"position\":1,\"name\":\"Home\",\"item\":\"https:\\\/\\\/incurelab.com\\\/wp\\\/\"},{\"@type\":\"ListItem\",\"position\":2,\"name\":\"UV Resin Bubbles: A Symptom-by-Symptom Diagnostic Guide\"}]},{\"@type\":\"WebSite\",\"@id\":\"https:\\\/\\\/incurelab.com\\\/wp\\\/#website\",\"url\":\"https:\\\/\\\/incurelab.com\\\/wp\\\/\",\"name\":\"INCURE INC.\",\"description\":\"Engineered Solutions. Trusted Worldwide\",\"publisher\":{\"@id\":\"https:\\\/\\\/incurelab.com\\\/wp\\\/#organization\"},\"potentialAction\":[{\"@type\":\"SearchAction\",\"target\":{\"@type\":\"EntryPoint\",\"urlTemplate\":\"https:\\\/\\\/incurelab.com\\\/wp\\\/?s={search_term_string}\"},\"query-input\":{\"@type\":\"PropertyValueSpecification\",\"valueRequired\":true,\"valueName\":\"search_term_string\"}}],\"inLanguage\":\"en-US\"},{\"@type\":\"Organization\",\"@id\":\"https:\\\/\\\/incurelab.com\\\/wp\\\/#organization\",\"name\":\"INCURE INC.\",\"url\":\"https:\\\/\\\/incurelab.com\\\/wp\\\/\",\"logo\":{\"@type\":\"ImageObject\",\"inLanguage\":\"en-US\",\"@id\":\"https:\\\/\\\/incurelab.com\\\/wp\\\/#\\\/schema\\\/logo\\\/image\\\/\",\"url\":\"https:\\\/\\\/incurelab.com\\\/wp\\\/wp-content\\\/uploads\\\/2025\\\/07\\\/incure-logo.jpeg\",\"contentUrl\":\"https:\\\/\\\/incurelab.com\\\/wp\\\/wp-content\\\/uploads\\\/2025\\\/07\\\/incure-logo.jpeg\",\"width\":164,\"height\":45,\"caption\":\"INCURE INC.\"},\"image\":{\"@id\":\"https:\\\/\\\/incurelab.com\\\/wp\\\/#\\\/schema\\\/logo\\\/image\\\/\"}},{\"@type\":\"Person\",\"@id\":\"https:\\\/\\\/incurelab.com\\\/wp\\\/#\\\/schema\\\/person\\\/53482b163015e8f48dc86f4132515727\",\"name\":\"Incure Content Team\",\"image\":{\"@type\":\"ImageObject\",\"inLanguage\":\"en-US\",\"@id\":\"https:\\\/\\\/secure.gravatar.com\\\/avatar\\\/85e856c6e17c9c44477ea1e0964ef5dc19c2a1ef29a741bb9bb742fcfc644fcc?s=96&d=mm&r=g\",\"url\":\"https:\\\/\\\/secure.gravatar.com\\\/avatar\\\/85e856c6e17c9c44477ea1e0964ef5dc19c2a1ef29a741bb9bb742fcfc644fcc?s=96&d=mm&r=g\",\"contentUrl\":\"https:\\\/\\\/secure.gravatar.com\\\/avatar\\\/85e856c6e17c9c44477ea1e0964ef5dc19c2a1ef29a741bb9bb742fcfc644fcc?s=96&d=mm&r=g\",\"caption\":\"Incure Content Team\"},\"url\":\"https:\\\/\\\/incurelab.com\\\/wp\\\/author\\\/kimleelcy\"}]}<\/script>\n<!-- \/ Yoast SEO plugin. -->","yoast_head_json":{"title":"UV Resin Bubbles: A Symptom-by-Symptom Diagnostic Guide - INCURE INC.","robots":{"index":"index","follow":"follow","max-snippet":"max-snippet:-1","max-image-preview":"max-image-preview:large","max-video-preview":"max-video-preview:-1"},"canonical":"https:\/\/incurelab.com\/wp\/how-to-prevent-bubbles-in-uv-resin-the-ultimate-guide","og_locale":"en_US","og_type":"article","og_title":"UV Resin Bubbles: A Symptom-by-Symptom Diagnostic Guide - INCURE INC.","og_description":"Not every bubble defect in cured UV resin has the same cause, and treating them all with the same fix \u2014 usually “add more vacuum degassing” \u2014 wastes process time on defects that vacuum degassing was never going to solve in the first place. Symptom: Fine Pinholes Scattered Across the Surface Surface pinholes, distinct from […]","og_url":"https:\/\/incurelab.com\/wp\/how-to-prevent-bubbles-in-uv-resin-the-ultimate-guide","og_site_name":"INCURE INC.","article_published_time":"2026-01-07T13:10:58+00:00","article_modified_time":"2026-09-12T00:43:01+00:00","author":"Incure Content Team","twitter_card":"summary_large_image","twitter_misc":{"Written by":"Incure Content Team","Est. reading time":"4 minutes"},"schema":{"@context":"https:\/\/schema.org","@graph":[{"@type":"Article","@id":"https:\/\/incurelab.com\/wp\/how-to-prevent-bubbles-in-uv-resin-the-ultimate-guide#article","isPartOf":{"@id":"https:\/\/incurelab.com\/wp\/how-to-prevent-bubbles-in-uv-resin-the-ultimate-guide"},"author":{"name":"Incure Content Team","@id":"https:\/\/incurelab.com\/wp\/#\/schema\/person\/53482b163015e8f48dc86f4132515727"},"headline":"UV Resin Bubbles: A Symptom-by-Symptom Diagnostic Guide","datePublished":"2026-01-07T13:10:58+00:00","dateModified":"2026-09-12T00:43:01+00:00","mainEntityOfPage":{"@id":"https:\/\/incurelab.com\/wp\/how-to-prevent-bubbles-in-uv-resin-the-ultimate-guide"},"wordCount":809,"publisher":{"@id":"https:\/\/incurelab.com\/wp\/#organization"},"inLanguage":"en-US"},{"@type":"WebPage","@id":"https:\/\/incurelab.com\/wp\/how-to-prevent-bubbles-in-uv-resin-the-ultimate-guide","url":"https:\/\/incurelab.com\/wp\/how-to-prevent-bubbles-in-uv-resin-the-ultimate-guide","name":"UV Resin Bubbles: A Symptom-by-Symptom Diagnostic Guide - INCURE INC.","isPartOf":{"@id":"https:\/\/incurelab.com\/wp\/#website"},"datePublished":"2026-01-07T13:10:58+00:00","dateModified":"2026-09-12T00:43:01+00:00","breadcrumb":{"@id":"https:\/\/incurelab.com\/wp\/how-to-prevent-bubbles-in-uv-resin-the-ultimate-guide#breadcrumb"},"inLanguage":"en-US","potentialAction":[{"@type":"ReadAction","target":["https:\/\/incurelab.com\/wp\/how-to-prevent-bubbles-in-uv-resin-the-ultimate-guide"]}]},{"@type":"BreadcrumbList","@id":"https:\/\/incurelab.com\/wp\/how-to-prevent-bubbles-in-uv-resin-the-ultimate-guide#breadcrumb","itemListElement":[{"@type":"ListItem","position":1,"name":"Home","item":"https:\/\/incurelab.com\/wp\/"},{"@type":"ListItem","position":2,"name":"UV Resin Bubbles: A Symptom-by-Symptom Diagnostic Guide"}]},{"@type":"WebSite","@id":"https:\/\/incurelab.com\/wp\/#website","url":"https:\/\/incurelab.com\/wp\/","name":"INCURE INC.","description":"Engineered Solutions. Trusted Worldwide","publisher":{"@id":"https:\/\/incurelab.com\/wp\/#organization"},"potentialAction":[{"@type":"SearchAction","target":{"@type":"EntryPoint","urlTemplate":"https:\/\/incurelab.com\/wp\/?s={search_term_string}"},"query-input":{"@type":"PropertyValueSpecification","valueRequired":true,"valueName":"search_term_string"}}],"inLanguage":"en-US"},{"@type":"Organization","@id":"https:\/\/incurelab.com\/wp\/#organization","name":"INCURE INC.","url":"https:\/\/incurelab.com\/wp\/","logo":{"@type":"ImageObject","inLanguage":"en-US","@id":"https:\/\/incurelab.com\/wp\/#\/schema\/logo\/image\/","url":"https:\/\/incurelab.com\/wp\/wp-content\/uploads\/2025\/07\/incure-logo.jpeg","contentUrl":"https:\/\/incurelab.com\/wp\/wp-content\/uploads\/2025\/07\/incure-logo.jpeg","width":164,"height":45,"caption":"INCURE INC."},"image":{"@id":"https:\/\/incurelab.com\/wp\/#\/schema\/logo\/image\/"}},{"@type":"Person","@id":"https:\/\/incurelab.com\/wp\/#\/schema\/person\/53482b163015e8f48dc86f4132515727","name":"Incure Content Team","image":{"@type":"ImageObject","inLanguage":"en-US","@id":"https:\/\/secure.gravatar.com\/avatar\/85e856c6e17c9c44477ea1e0964ef5dc19c2a1ef29a741bb9bb742fcfc644fcc?s=96&d=mm&r=g","url":"https:\/\/secure.gravatar.com\/avatar\/85e856c6e17c9c44477ea1e0964ef5dc19c2a1ef29a741bb9bb742fcfc644fcc?s=96&d=mm&r=g","contentUrl":"https:\/\/secure.gravatar.com\/avatar\/85e856c6e17c9c44477ea1e0964ef5dc19c2a1ef29a741bb9bb742fcfc644fcc?s=96&d=mm&r=g","caption":"Incure Content Team"},"url":"https:\/\/incurelab.com\/wp\/author\/kimleelcy"}]}},"rttpg_featured_image_url":null,"rttpg_author":{"display_name":"Incure Content Team","author_link":"https:\/\/incurelab.com\/wp\/author\/kimleelcy"},"rttpg_comment":0,"rttpg_category":"<a href=\"https:\/\/incurelab.com\/wp\/category\/uncategorized\" rel=\"category tag\">Uncategorized<\/a>","rttpg_excerpt":"Not every bubble defect in cured UV resin has the same cause, and treating them all with the same fix \u2014 usually “add more vacuum degassing” \u2014 wastes process time on defects that vacuum degassing was never going to solve in the first place. Symptom: Fine Pinholes Scattered Across the Surface Surface pinholes, distinct from…","_links":{"self":[{"href":"https:\/\/incurelab.com\/wp\/wp-json\/wp\/v2\/posts\/14243","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/incurelab.com\/wp\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/incurelab.com\/wp\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/incurelab.com\/wp\/wp-json\/wp\/v2\/users\/9"}],"replies":[{"embeddable":true,"href":"https:\/\/incurelab.com\/wp\/wp-json\/wp\/v2\/comments?post=14243"}],"version-history":[{"count":2,"href":"https:\/\/incurelab.com\/wp\/wp-json\/wp\/v2\/posts\/14243\/revisions"}],"predecessor-version":[{"id":24258,"href":"https:\/\/incurelab.com\/wp\/wp-json\/wp\/v2\/posts\/14243\/revisions\/24258"}],"wp:attachment":[{"href":"https:\/\/incurelab.com\/wp\/wp-json\/wp\/v2\/media?parent=14243"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/incurelab.com\/wp\/wp-json\/wp\/v2\/categories?post=14243"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/incurelab.com\/wp\/wp-json\/wp\/v2\/tags?post=14243"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}