An opaque shield solves the UV exposure problem and creates a new one: an operator who has to lift it to check on the cure is an operator who’s back in the exposure path anyway.
The Primary Containment Piece
The Incure Perimeter™ PRM-FRONT, one piece in the Incure Perimeter™ UV Safety Shields lineup, is the primary UV containment shield for F-Series™ flood lamps, wrapping around the lamp and stand assembly to block scatter UV headed directly at the operator — the direction that matters most on a shared production floor. It mounts to the shared F-Series™ stand rather than to an individual lamp head, so one shield size fits the F100, F200, F200P, F400, and F500. The F900P uses a different, larger stand and isn’t compatible.
Tinted Acrylic, Not Opaque Metal
Where a fully opaque enclosure blocks the operator’s view of the part along with the UV, the PRM-FRONT’s tinted acrylic body lets the operator monitor the assembly and watch the cure cycle progress without lifting or removing the shield. On a station where the operator is also visually inspecting fillet coverage or part placement mid-cycle, that visibility is a real workflow advantage over a solid barrier that trades safety for line of sight.
No Tools, No Fasteners
An integrated carry handle lets the shield lift on and off the F-Series™ stand without any fasteners or hardware. That matters on lines that swap lamp configurations between product runs, or move a station’s shielding for maintenance access — the PRM-FRONT installs and comes off in seconds, fast enough that it doesn’t become a reason to skip using it between quick changeovers.
Confirming which F-Series™ stand configuration a given line is running, before ordering a shield sized for it, avoids a mismatch at install — Email Us with your F-Series™ model and Incure can confirm fit.
Front Coverage Is Not Full Coverage
The PRM-FRONT is deliberately scoped to the direction that matters most for the operator standing at the station, and it’s worth being explicit about what it doesn’t cover: low-level backside radiation still escapes behind the lamp stand. On shared floors where personnel or sensitive equipment sit behind the station as well as in front of it, that gap matters enough to close rather than leave open. Full 360° enclosure requires pairing the PRM-FRONT with a supplemental rear shield built specifically to complete it — a companion accessory in the same Incure Perimeter™ line.
A shielding plan should account for every direction UV can scatter, not just the one facing the operator. Review the Incure F-Series™ UV Arc Flood Lamps this shield is built to fit, and confirm your team’s Incure Vison™ eyewear is rated for F-Series™ output as a second layer of protection alongside physical shielding.
Sizing and Weight
The PRM-FRONT measures 12 × 11.5 × 11 inches and weighs 6 lbs — light enough for one operator to lift on and off by the integrated handle without assistance, but substantial enough to sit securely on the F-Series™ stand without additional bracing. It’s rated for the F100, F200, F200P, F400, and F500 stand family; the F900P’s larger stand requires a different shielding solution not covered by the Perimeter™ line.
Pairing Physical Shielding With PPE, Not Replacing It
A shield rated to contain forward-scattered UV reduces exposure risk across a station, but it isn’t a substitute for personal eye protection on the operator actually working closest to the lamp during load and unload. Treating the PRM-FRONT as one layer in a broader UV safety approach — physical containment plus rated eyewear — is a more realistic safety posture than relying on the shield alone to fully eliminate exposure risk at close range.
Compatibility Check Before Ordering
Because the PRM-FRONT mounts to the shared F-Series™ stand rather than an individual lamp head, confirming which stand configuration a station actually runs is the one detail that matters most before ordering. A station running an F900P on its larger stand needs a different shielding approach entirely — attempting to fit a PRM-FRONT to that configuration simply won’t work, regardless of how well it fits the rest of the F-Series™ family. For every other stand-mounted model, one PRM-FRONT size covers the whole range without a per-model SKU to track.
Where the PRM-FRONT Earns Its Keep
Three floor layouts consistently justify adding front shielding: shared production floors, where the shield blocks stray UV from reaching adjacent operators and equipment working near an F-Series™ station rather than isolating the process in a dedicated room; multi-operator assembly cells, where an F-Series™ curing step needs to run beside other manual work without forcing a physical separation between stations; and R&D or QC benches, where UV curing equipment often sits on a shared lab bench alongside other instruments and personnel. In each case, the PRM-FRONT’s combination of visibility and no-tools installation is what makes it practical to use consistently rather than skip when the station gets busy.
For a full review of your F-Series™ station layout, Contact Our Team.
Visit www.incurelab.com for more information.