A shield that only covers the direction the operator faces is doing half the job on any floor where equipment or people sit behind the lamp station too.
The Supplemental Piece, Not a Standalone Solution
The Incure Perimeter™ PRM-REAR, part of the Incure Perimeter™ UV Safety Shields lineup, is the supplemental shield for F-Series™ flood lamps — it doesn’t replace primary front-of-lamp containment, it completes it. Where a front shield blocks scatter UV headed at the operator, the PRM-REAR secures under the F-Series™ stand’s mounting feet to block the low-level backside radiation that escapes behind the station regardless of how well the front is contained. Add it when personnel or sensitive equipment share the space behind an F-Series™ curing station.
Flared Panels That Don’t Fight the Front Shield’s Tilt
The PRM-REAR’s side panels are flared specifically to clear a front shield’s normal lamp-tilt adjustment range, so both pieces install together without either one obstructing the other or restricting the lamp’s usual range of motion. That’s a deliberate design choice rather than a coincidence — a rear shield that blocked tilt adjustment would force operators to choose between full enclosure and normal process flexibility, and the PRM-REAR is built so that trade-off never comes up.
No Attachment Hardware Required
Unlike a front shield that lifts on and off by an integrated handle, the PRM-REAR needs no hardware on the shield itself — it slides under the F-Series™ stand’s mounting feet and is held in place by the stand’s own weight. Installation and removal take seconds and require no tools, which matters on lines where the shielding configuration changes along with the lamp setup between product runs.
Confirming stand compatibility before ordering avoids a mismatch — the PRM-REAR fits the same F100, F200, F200P, F400, and F500 stand family as the rest of the Perimeter™ line, but not the F900P’s larger stand. Email Us with your F-Series™ configuration and Incure can confirm fit.
Full-Enclosure Documentation for UV Safety Programs
Beyond the physical containment, pairing a rear shield with a front shield supports facilities that need to document full-perimeter UV exposure controls as part of a broader UV safety and PPE compliance program — a gap in backside coverage is the kind of finding that shows up in a walkthrough audit even when the operator-facing side is fully compliant. Closing that gap with a purpose-built Incure accessory is simpler than fabricating a barrier in-house.
A complete shielding plan accounts for every direction UV scatters, not just the side the operator sees. Review the Incure F-Series™ UV Arc Flood Lamps this shield is built to fit, and confirm your team’s Incure Vison™ eyewear is rated for F-Series™ output as a second layer of protection.
Sizing and Weight
The PRM-REAR measures 13 × 11 × 5 inches and weighs 6 lbs — a wider, lower-profile form factor than the front shield, matching its job of sliding under the stand’s mounting feet rather than wrapping around the lamp head itself. Like the front shield, it’s rated for the F100, F200, F200P, F400, and F500 stand family; it isn’t compatible with the F900P’s different, larger stand.
A Small Accessory With a Real Documentation Role
Beyond the physical exposure reduction, having a documented, purpose-built rear shield in place — rather than an improvised barrier — matters when a facility’s UV safety program is reviewed by an internal EHS team or an outside auditor. A gap in backside coverage found during a walkthrough is a straightforward finding to close with an Incure accessory built for exactly that purpose, rather than requiring a custom fabrication project to address after the fact.
It Requires the Front Shield First
The PRM-REAR is explicitly a supplemental accessory, not a standalone product — it’s built to pair with a PRM-FRONT already installed, not to replace primary front-of-lamp containment on its own. Ordering the rear shield without the front piece leaves the direction of greatest UV exposure risk — straight at the operator — unaddressed while only closing the lower-priority backside gap. Confirming the front shield is already specified, or ordering both together, avoids ending up with a partial containment setup that looks complete on paper but isn’t.
Where Full Enclosure Actually Matters
The PRM-REAR is worth adding specifically on two kinds of floor layouts: shared production floors where personnel or equipment routinely work behind an F-Series™ station as well as in front of it, and multi-operator assembly cells where a station is genuinely accessed from more than one side during a shift. On a station against a wall or facing an aisle with no traffic behind it, the front shield alone may already contain the practical UV exposure risk — the rear shield’s real value shows up once the space behind the lamp stand is actually occupied during operation, not as a default add-on to every F-Series™ install regardless of layout.
For a full review of your F-Series™ station layout, Contact Our Team.
Visit www.incurelab.com for more information.