S20™ Base Unit — UV Arc Spot Curing Controller (No Lightguide)
Incure S20-BASE is the S20™ spot curing controller — without a fixed lightguide configuration, and without the commitment to one. Where the S20-1P through S20-4P bundle the controller with a specific pole count, the S20-BASE delivers the same >21 W/cm² UVA output as the standalone platform you pair with any S20™-compatible liquid lightguide assembly purchased separately. Programmable 1–99 second timer, 25–100% intensity control, constant power regulation within ±1.0%. One controller. Any configuration.
One Controller — Any S20™ Lightguide Configuration
The S20-BASE accepts any S20™-compatible liquid lightguide assembly — 1-pole through 4-pole — without hardware changes. Change your pole count as your process evolves: add a 2-pole lightguide for dual-joint assemblies, swap to 4-pole for a high-throughput fixture. The controller never needs replacing when production requirements change.
One Controller Across Your Entire S20™ Lightguide Inventory
Labs and production cells that service multiple part families maintain separate lightguide assemblies — different pole counts or tip diameters for each job. The S20-BASE runs them all from one controller. Add or replace individual assemblies without a parallel controller investment. Controller cost is shared across every S20™-compatible lightguide configuration you operate.
>21 W/cm² Available to Any Connected Lightguide
The full S20™ output — >21 W/cm² UVA at the source — is delivered to whichever lightguide configuration is connected, with constant power regulation within ±1.0%. Performance is identical to any S20™ configured unit: same lamp, same electronics, same intensity at the lightguide input.
| Specifications | ||
| Model | S20-BASE | |
| 100–120 VAC | 200–240 VAC | |
| AC Input Voltage | 100–120VAC ±10% | 200–240VAC ±10% |
| AC Input Current | 4.7 Amperes | 2.5 Amperes |
| Source Input Frequency | 47 Hz to 63 Hz | |
| Lamp Power Regulation | ±1.0% | |
| Fan / Auxiliary Voltage | 24V @ 0.5A | |
| Lamp Type | 200 Watt Mercury Arc | |
| Burning Position | Horizontal | |
| Radiation Flux | 275–650 nm | |
| Warm-up Time | 1 to 2 minutes | |
| Cooling Time Before Restart | 2 to 5 minutes typical | |
| Output Intensity (Typical) | >21 W/cm² UVA (at source) | |
| Output Intensity Range | 25–100% adjustable | |
| Timer Range | 1–99 seconds (programmable) | |
| Lamp Life | >2,000 hours typical | |
| Operating Temperature | +10°C to +40°C / +50°F to +104°F | |
| Relative Humidity | 30–75% operating, 10–100% storage | |
| Cooling | Dual DC Fans, Filtered | |
| Over-temp Shutdown | 65°C (internal) | |
| Platform Compatibility | ||
| Compatible Lightguide Assemblies | S20™ 1-Pole (S20-1P), 2-Pole (S20-2P), 3-Pole (S20-3P), 4-Pole (S20-4P) | |
| Lightguide (Supplied) | None — Lightguide Assemblies Sold Separately | |
| Safety Equipment | UV Protective Goggles Supplied With Each Lightguide Assembly | |
| Physical | ||
| L × W × H (Controller) | 10.6″ × 8.7″ × 4.1″ | |
| Weight | 6.0 lbs (2.7 kg) | |
| Ordering | ||
| P/N | S20-BASE | |
Output intensity is measured at the lightguide input port with the system operating at 100% power. Actual irradiance at the cure point varies with lightguide type, pole count, tip diameter, length, and optical component condition. Lightguide assemblies sold separately — see individual S20™ model datasheets for lightguide-specific intensity values.
