UV LED Flood Conveyor Curing System — Incure CDM™ + L64
Incure CDM™ L64 is the 4-inch-lane-sized alternative to the CDM™ + L88 — a UV LED flood conveyor curing system pairing the CDM™ 9″ polypropylene belt conveyor with a 6″×4″ flood head shaped for the standard 4-inch PCB panel lane, where the wider L88 configuration over-irradiates. Delivered as a complete system — conveyor chassis plus lamp head — it provides 1,900 mW/cm² at 385/395/405 nm (1,600 mW/cm² at 365 nm) at 2″ working distance, belt-speed dose control from 4,750 to 38,000 mJ/cm² UVA, PLC / RS-232 / foot-switch integration, and >20,000-hour LED service life for inline adhesive bonding, conformal coating, and encapsulant cure at up to 4″ maximum part width.
Full 6″×4″ Flood Area — No Beam Alignment Between Runs
The L64 flood head delivers UV simultaneously across the entire 6″×4″ curing footprint — unlike M-Series focused-beam configurations (M51: 5″×1″, M62: 6″×2″) that require the bond line to track precisely through a narrow beam width. Parts up to 4″ wide cure in a single pass without fixturing adjustments or beam-position setup between product changeovers.
6″×4″ Non-Square Format Fits the Standard 4-Inch PCB Panel Lane
Standard PCB panel conveyors run 4-inch lane fixtures. The L64's 6″ illumination length along the belt-travel direction covers standard panel gap-to-gap spacing, while the 4″ width bounds the lane precisely — irradiating only the assembly without wasting UV dose on belt material or fixture hardware outside the panel edge. The L88 (8″×8″) over-irradiates laterally on a 4-inch lane; the L64 is shaped for it.
1,900 mW/cm² at 385/395/405 nm — Full Flood Intensity at 4″ Part Width
The L64 delivers the same 1,900 mW/cm² peak intensity at 2″ working distance as the wider L88 configuration, in the 6″×4″ non-square footprint sized for standard PCB panel tracks and 4-inch fixture lanes — without paying for the 8″×8″ L88 area that 4″-wide assemblies never use.
| Lamp Head | |
| Model | L64 |
| Curing Area | 6″ × 4″ (152 mm × 102 mm) |
| LED Array | 216 LEDs |
| Available Wavelengths | 365 nm · 385 nm · 395 nm · 405 nm (factory-configured at order) |
| Curing Performance | |
| Peak Intensity @ 365 nm, 2″ | 1,600 mW/cm² |
| Peak Intensity @ 385/395/405 nm, 2″ | 1,900 mW/cm² |
| Curing Energy @ 1.5 ft/min (slowest) | 38,000 mJ/cm² UVA · 32,000 mJ/cm² UVV |
| Curing Energy @ 6.0 ft/min (nominal) | 9,500 mJ/cm² UVA · 8,000 mJ/cm² UVV |
| Curing Energy @ 12.0 ft/min (fastest) | 4,750 mJ/cm² UVA · 4,000 mJ/cm² UVV |
| Dynamic Uniformity @ 2″ on Conveyor | 0.89 |
| Static Uniformity @ 2″ on Conveyor | 0.80 |
| Light Source Useful Life | > 20,000 hours |
| Typical Intensity Loss Over Useful Life | ≤ 20% |
| Conveyor Platform | |
| Belt Material | 9″ Polypropylene — anti-static option available |
| Belt Speed | 1.5–12.0 ft/min (adjustable) |
| Maximum Part Width | 4 inches (102 mm) |
| Conveyor Curing Height | 0.5″–2.0″ (adjustable) |
| Mounting Stand | Optional |
| Cooling | Forced-air cooling |
| Control & Power | |
| External Control | PLC · RS-232 · Foot Switch |
| Operating Mode | Timer / Continuous (switchable) |
| Power Input | 100–240 V, 50/60 Hz, auto-ranging |
| Ordering | |
| P/N at 365 nm | CDM-1xL64-365 |
| P/N at 385 nm | CDM-1xL64-385 |
| P/N at 395 nm | CDM-1xL64-395 |
| P/N at 405 nm | CDM-1xL64-405 |
Peak intensity at 385/395/405 nm exceeds 365 nm output for the L64 array — this is a characteristic of LED die efficiency at these wavelengths. LED curing energy values are estimated based on measured irradiance profile, illuminated length in the belt-travel direction, and belt speed. Actual dose may vary depending on working distance, beam profile, part height, reflectivity, and measurement method. Uniformity values are typical measurements on the CDM™ conveyor, with ±5% measurement variation. Per-configuration wattage, machine dimensions, and weight available on request. Wavelength is factory-configured at time of order — contact Incure for wavelength selection guidance based on adhesive photoinitiator absorption peak.
